Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Illustration shown here features a right hand seat wall unit with all options. Use installation instructions provided with product. Product specifications are subject to change without notice. INSTALLATION INSTRUCTIONS Important: Read complete instructions before beginning installation. Review instructions for all optional items being considered for installation before completing rough-in. The successful installation of the options may require some modifications to be made to the custom shower system or the rough-in structure before completion. Check for shipping damage upon receipt of the custom shower system. Jacuzzi Whirlpool Bath is not responsible for damage sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims on the outside of the carton and immediately file a claim with the carrier. Once the components have been removed from the carton and before it is permanently installed, check the parts completely for damage resulting from shipping or handling. All Jacuzzi Whirlpool Bath products are factory tested for fit and finish prior to shipping. If problems are detected, immediately notify your Jacuzzi Whirlpool Bath dealer or Authorized Service Agent, or call Jacuzzi Whirlpool Bath, (800) 288-4002, for Warranty Service. NOTE: Damage or defects which could have been discovered and repaired prior to installation and which are claimed after final installation of the shower system are excluded from our warranty. STEP 1. ROUGH-IN FRAMING DETAILS ROUGH-IN DIMENSION CHART MODEL A B C D E F 4242N 42-1/8" 42-1/8" 16" 16" 27" 12-3/8" 4848N 48-1/2" 48-1/8" 16" 16" 32-1/4" 16-3/8" E B D A F C LC E B D A F C CROSS SUPPORT LC E LCLC E SHOWN WITH 2 SHELF WALLS SHOWN AS A RIGHT HAND SEAT WALL STEP 2. ROUGH-IN PLUMBING A. Install water lines and rough plumbing. Valve should be located between 36" and 48" from the floor. Use blocking and secure with pipe straps. B. If stationary shower is used, install shower riser. Suggested shower head location is 78" from the floor (above the endwall). C. The locations of the valves, mixers, and shower head should be determined before the walls are placed in position. Where access to connections is limited, allow enough flexibility in the supply lines for easier positioning of the valves after the unit is in place. From stable reference points such as subfloor and front of the double studs, measure and note the locations of the valves, shower head arm and connection for body spray jets. STEP 3 Install Shower Base per Shower Base Instructions. A. For proper fit and installation of the custom shower system it is imperative that the shower base is level on all sides and the wall structure is plumb. NOTE: Watertight installation of the drain is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty of this product. (See “Drain Installation Instructions” provided with drain.) ROUGH-IN PLUMBING DETAILS SUPPLY LINES OPTICA 300 MIXER AND TRANSFER VALVE BLOCKING TO SHOWER HEAD TO BODY SPRAY JETS WALL (IF NEO WALL IS EQUIPPED WITH JETS) 78" (FOR FIXED SHOWER HEAD) 36" MIN. 48" MAX. 24" 12" CLEARANCE FOR PLUMBING AT SEATWALL CENTERLINE SUGGESTED PLUMBING LAYOUT (REVERSE FOR LEFT HAND SEAT WALL VERSION) LINE TO BODY SPRAY JETS WALL (IF BACK WALL IS EQUIPPED WITH JETS) OPTICA 300 MIXER/ TRANSFER VALVE HOT WATER SUPPLY COLD WATER SUPPLY LINE TO WALL BAR SHOWER HEAD OR SHOWER HEAD OPTICA 300 CONNECTIONS TO SHOWER HEAD OR HAND HELD SHOWER TO BODY MxF ADAPTER (3) COPPER GASKET (4) HOT IN SPRAY WALL TRANSFER VALVE LEFT-HAND THREAD TO SWEAT ADAPTER COPPER PIPE COLD IN MIXER VALVE STEP 4. BACK OR BODY SPRAY INSTALLATION A. Attach the pins to the wall, (5) per side. B. Temporarily place wall in position on the base and against the corner stud wall. C. Temporarily place the shelf wall and seat wall in position by engaging the pins and holes. D. Line up system walls and base at the front. Shim the back or body spray wall top flange if necessary. E. Remove all walls. Hook up plumbing from transfer valve to body spray plumbing. F. Place a 1/4" bead of caulking at the bottom of the shower base flange where the wall will sit. G. Place a 1/4" to 1/2" bead of construction adhesive on each stud where the back surface of the panel stiffeners will make contact. H. Place the wall in position on the shower base. Secure the top flange to the stud wall using #6 drywall screws. The wall must remain seated and flush on the shower base to ensure a matching joint to the sidewall. I. Secure the two side flanges to the side stud walls using #6 drywall screws. Shim between the flange and studs as required to maintain plumb walls. STEP 5. SEAT WALL INSTALLATION A. Temporarily place the seat wall in position resting the seat wall on the base. Make certain the wall and base are in line at the front notch. Remove the seat wall. C. Mark valve locations on the back side of the panel if there is access. Remove the shelf wall and drill fa...