Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. AC Power This fixture has an auto-switching power supply that can accommodate a wide range of input voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages. This fixture will accommodate between 100 V and 240 VAC, 50/60 Hz. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. All fixtures must be connected to circuits with a suitable Earth Ground. Contact Us World Wide General Information CHAUVET® 3000 North 29th Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084 Technical Support CHAUVET® 3000 North 29th Court Hollywood, FL 33020 voice: 954.929.1115 (Press 4) fax: 954.929.5560 (Attention: Service) World Wide Web Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. . Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. . Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. . This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain or moisture. . Make sure there are no flammable materials close to the unit while operating. . The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces. Be sure that no ventilation slots are blocked. . Secure fixture to fastening device using a safety chain. . Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher than this. . In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. . Never connect the device to a dimmer pack. . Make sure the power cord is never crimped or damaged. . Never disconnect the power cord by pulling or tugging on the cord. . Avoid direct eye exposure to the light source while it is on. There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET at: 954-929-1115. 2. INTRODUCTION Features . Extremely compact LED pinspot . High-power, 3 W (700 mA) LED . Includes multiple lenses to change beam angles Product Overview Hanging bracket Bracket adjustment knob 148 mm 5.9 in 193 mm 7.6 in 105 mm 4.2 in C:\Documents and Settings\tw\My Documents\current manuals in progress\LED PinSpot 2\005 - Images\Line Drawings\cover3.gif \\10.0.0.203\backups\User Manuals\001 - Chauvet Club-DJ\001 - Chauvet Prerelease-CLUB_DJ\LED PinSpot 2\005 - Images\Line Drawings\lens-ring.gif \\10.0.0.203\backups\User Manuals\001 - Chauvet Club-DJ\001 - Chauvet Prerelease-CLUB_DJ\LED PinSpot 2\005 - Images\Line Drawings\lens.gif Mounting Orientation This fixture may be mounted in any safe position, provided there is adequate room for ventilation. Hanging Clamp Note! Clamp is sold separately. Rigging It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. . When selecting installation location, take into consideration lamp replacement access and routine maintenance. . Safety cables must always be used. . Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation. Lens Replacement This fixture comes with an optional lens that modifies the beam angle. Please see the instructions below for instructions on replacing the lens. 1. Remove the retainer ring. 2. Remove the lens (the lens will fall out without the retainer ring installed). 3. Insert the new lens. Use caution, as it may fall out until the retainer ring is installed in step #4! 4. Install the retainer ring. 5. Assure that the installation is tight. If the lens is not installed properly, it may fall out. This may be a safety hazard if installed overhead. Lens Retainer Ring 3. APPENDIX General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequ...