Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Long exposure at higher temperature can result in dizziness and/or hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98°F (36.7°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness or lethargy. The affects of hyperthermia include: • Unawareness of impending hazard • Failure to perceive heat • Failure to recognize the need to exit the spa • Physical inability to exit the spa • Fetal damage in pregnant women • Unconsciousness resulting in a danger of drowning Children should be supervised at all times. DO NOT OPERATE SPA WITHOUT CORRECT WATER LEVEL! Keep all jets under water with exception of “neck jets”. Actual features included in spa’s descriptions and photos are subject to change without notice. 2 Installation - Spa placement Spa Location: Improper installation may result in equipment damage and will void the warranty. Your spa must be placed on a flat, level surface. The space you choose to install your spa is a very important decision, you should consider all of the listed suggestions. Check your local code office for understanding of building, fencing, gates, electrical, plumbing and enclosure required codes. A location should be selected to compliment your lifestyle, the view from your house and the ability to supervise the spa. Position the spa in relation to the surroundings of trees, sunlight exposure, wind, bathroom location, landscaping and evening lighting. The spa with water is very heavy, if the spa is placed on flooring or decking, be sure the structure is strong enough to support the weight. The necessary support should be at least 75 pounds per square foot. Install your spa, in a way that will allow easy access to the equipment door. Storage area for maintenance equipment and chemicals (storing chemicals inside your spa cabinet will void the warranty) Indoor Considerations: All of the interior of the spa location must be able to withstand high humidity. The spa chemicals may have some corrosive effect. Floor drain is needed to carry off splashed water from the spa. It is strongly advised NOT to locate a spa on second story location that may be above finished living space. 3 Electrical - General Instructions It is recommended that a licensed electrician install the power to your spa, in accordance with the National Electric Code or any local electrical codes in effect at the time of installation. Power supply installation must include a properly rated GFCI circuit breaker. The circuit breaker must be dedicated and cannot be shared with any other appliances. It should be labeled and easily accessible to users. Power supply must be hard wired into the power pack. DO NOT USE EXTENSION OR PLUG-TYPE CORDS OF ANY KIND. The use of a shut-off box near the spa is recommended. Metal surfaces within 5 feet of the spa must be grounded to the spa. 220V Barcelona Electrical Connections: This change must be performed by a certified electrician. Three Wire & Ground These wires go to the PC Board Control Circuit. TERMINAL BLOCK GRD L1 L2 N Connections should be made using copper conductors only. The connecting wire and circuit breakers or fuses must be sized to accommodate the total ampere load as specified on the equipment module data label. Strong Pools and Spas only makes electrical recommendations, always consult a certified electrician. 4 Control Panel Identification Mode Mode key will change your spa - 3 different modes 1. Standard - Normal spa usage 2. Economy - Maintains temperature slightly lower than desired 3. Sleep - Keeps temperature approximately 20. below set temperature for inactive use Mode is changed by pushing warm of cool keys with mode key. Jet 1 Jet 1 controls pump 1 operation. Press firmly and then release, give time for system to react. Pump operates in three different speeds. 1. Off if temperature is reached and filter is not engaged. 2. Low speed for filter mode. along with heating periods and any time customer prefers. 3. High when customer prefers, stays on only for 30 minutes at a time. Jet 2 Jet 2 key controls pump 2. Operates on three (3) speeds. OFF- LOW - HIGH Light There are several color options in our spas and by pressing the light button in quick succession the customer can cycle through the different lighting options. Warm Press Warm to increase temperature. Once released, the controls will go back to the current temperature display. Cool Press Cool to decrease temperature. Once released, the controls will go back to the current temperature display. Option This key is not used to activate any operation in Strong spas. BEFORE START UP! IMPORTANT UNION ADJUSTMENTS There are SIX unions that require hand tightening prior to operation of your spa. When filling the spa with water, keep observing these fittings for any slight water drips. If a drip is observed, just hand tighten until dripping ceases. 5 Startup Preparations -Make sure that if spa is equipped with g...