Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
The kit includes the specially designed silicon nitride igniter and six different bracket configurations to adapt the igniter to the specific applianceapplication along with accessory parts to allow mounting andwiring the igniter. Clear instructions and application templates are provided to simplify selection of the proper bracket andease installation of the replacement. BEFORE YOU START 1. Review this instruction sheet fully to ensure you arefamiliar with the steps and information necessary to complete the installation properly, including the WARNING section on this page. 2. Confirm the existing hot surface igniter has failed: a. Run an appliance cycle and observe the installed igniter. b. If the igniter glows, the problem is not the igniter. c. If the igniter does not glow during an ignition cycle: (1) Unplug the igniter lead wires. (2) Set a voltmeter’s scale to 300 VAC and connect the voltmeter to the igniter harness. (3) Run another cycle and confirm 120 VAC powerat the harness during the igniter warm up time. 3. Check the appliance construction and wiring diagram (typically located on an appliance panel) and confirm that the appliance does not use the hot surface igniter as the flame sensor. Do not use the CQ8000A kit if the existing igniter is also the flame sensor. Use an originalequipment part. The CQ8000A is not designed to be used as a flame sensor. 4. If the appliance is a sealed combustion model, determine if the existing hot surface igniter ceramic is part of the sealing of the burner box. If it is, check carefully to determine if this kit will allow the proper appliance function. 5. Confirm the kit components: a. six brackets stamped A, B, C, D, E, and F b. one hot surface igniter with wiring leads c. two wire nuts and a thread forming screw 6. The CQ8000A should not be handled by the black silicon nitride igniter. Use care to handle the CQ8000A by the ceramic casing or the bracket. INSTALLATION When Installing This Product… 1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition. 2. Check the cross-reference table on page 4 and the templates (Fig. 1 and Fig. 2) to make sure the proper igniter bracket is used for your application. 3. This product is intended for installation by a trained and experienced service technician. If a service technician is not available, the individual installing this product must be knowledgeable in the design, construction, and operation of the gas fired appliance being serviced. 4. After installation is complete, check out appliance operation as provided in these instructions. WARNING Fire or Explosion or Electrical Shock Hazard. Can cause severe injury, death or property damage. 1. Never install where water can flood, drip or condense on the igniter or its controller. 2. Liquefied petroleum (LP) gas is heavier than air and will not naturally vent upward. — Do not operate electric switches, lights, or appliances until you are sure the appliance area is free of gas. 3. Disconnect power supply before beginning wiring or making wiring connections to prevent electrical shock or equipment damage. 4. The CQ8000A is NOT designed to replace silicon carbide hot surface igniters in residential gas ovens orresidential clothes dryers. Use of this product in a residential gas oven or residential gas clothes dryer can result in severe injury, death, or property damage. Remove the old igniter assembly 1. Turn off electrical power supply external to the appliance. 2. Turn off gas supply to the appliance. 3. Set thermostat to the lowest setting or OFF. 4. Remove the appliance panel to expose the burner area. If necessary remove the burner box panel to expose theinstalled igniter. 5. Disconnect the installed igniter from the appliance wiringharness and move the wiring harness out of the way. 6. Carefully review the location of the installed igniter in theappliance. Pay attention to where the igniter is locatedrelative to the burners and other parts of the appliance. This will help confirm the location of the new igniter for installation. 7. Locate and remove the screw(s) holding the installedigniter or igniter bracket assembly in place. Remove the installed igniter very carefully to avoid damaging it. Retain the screw(s) for re-installation. 69-2460EFS-03 CQ8000A UNIVERSAL HOT SURFACE IGNITER KIT CQ8000A UNIVERSAL HOT SURFACE IGNITER KIT : If there is an orange rubber gasket on the originalmetal bracket, carefully remove the gasket from theoriginal bracket and use it with the CQ8000A bracket E to support the replacement. Select the proper CQ8000A bracket 1. Use the cross-reference table to determine which igniter models are recommended for replacement. See Table 1 on page 4. 2. Using the bracket selection templates (Fig. 1 and Fig. 2), the cross-reference (Table 1), and the original igniter assembly, place the igniter on the templates to confirm which bracket to use for this installation. NOTES: 1. Each of the six bracke...