Assessments - , GPA: ( )

Instruções de Operação Invacare, Modelo 3600

Fabricante : Invacare
Arquivo Tamanho: 1.01 mb
Arquivo Nome : 1118387.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

If any part of the system is not functioning properly, DO NOT use the system. Have thesystem serviced to correct the problem. The system MUST be maintained on a regular basis to ensure it is functioning properly. Disinfecting Disinfect the tub after initial set up and ALWAYS disinfect the tub after each use to avoidresident infection and contamination of the tub. DO NOT disinfect the tub when it is occupied otherwise injury may occur. ALWAYS wear gloves, protective apron, and face shield protection when disinfecting orcleaning your tub. ALWAYS handle disinfectants, cleaning compounds, and powdered sanitizers with extreme care. Physical or mechanical damage caused by improper handling or usage ofsuch products will not be the responsibility of ICCI. DO NOT attempt to turn on whirlpool pump during the disinfectant cycle. Doing so could result in skin or eye contact with the disinfectant, which is corrosive. If contact ismade, rinse immediately with water. If irritation occurs, consult a physician. ALWAYS read and follow disinfectant label directions carefully. NEVER use abrasive cleaners like scouring powder or liquid cleaners containing pumice stone.The use of these typesofcleaners will makethe gel.coat finishof your tubscratched and dull. NEVER use cleaners containing iodine, bromine, Betadine® or methylene blue. The use ofthesetypesof cleaners will cause the tub to stain.Neverusecleanerscontaining bleach. Use of these types of cleaners will dry out the rubber seals and gaskets and the tubwill not function properly. Side Entry Whirlpool Tub 12 Part No 1118387 SECTION 1—GENERAL GUIDELINES Operation DANGER Keep hair and body away from suction guard when pump is running. The causes, symptoms, and effects of hyperthermia may be described as follows: Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include: • Failure to perceive heat • Failure to recognize the need to exit the spa or hot tub • Unawareness of impending hazard • Fetal damage in pregnant women • Physical inability to exit the spa or hot tub • Unconsciousness resulting in the danger of drowning The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. NEVER operate whirlpool without water level above the whirlpool jets. Severe pumpdamage will result. DO NOT operate this unit without the guard over the (water intake) suction fitting. The guard is a safety device that reduces the potential hazard of hair or body entrapment. To reduce the risk of injury, DO NOT permit children or infirm persons to use this unitunless they are supervised at all times. Recommended length of a bath is 5 to 10 minutes. However, if you become nauseous ordizzy or develop a headache, get out at once and cool down. Get medical attention ifsymptoms persist. Also, check with a physician before using this unit again. Anyone under a doctor.s supervision, pregnant, or with poor health, should check with aphysician before using this unit. Part No 1118387 13 Side Entry Whirlpool Tub SECTION 2—PARTS AND INSTALLATION SECTION 2—PARTS AND INSTALLATION Parts Information For parts information, please contact ICCI Technical Service at (800) 668.2337. About Installation WARNING Access for servicing the tub MUST be provided. Install the tub in a location that will permit access to the service panels, plumbing and electrical hook-ups. CAUTION DO NOT lift the tub by the plumbing. DO NOT remove or relocate the pump. Modifications to the pump location may cause the system to malfunction and will void the warranty. The tubs are free.standing side.entry bathing and hydromassage tubs which are secured to the floor. Preparing the Work Area NOTE: For this procedure, refer to FIGURE 2.1 on page 15. 1. Determine location for the tub installation. NOTE: Follow recommended floor plan shown in FIGURE 2.1 on page 15 when installing the tub. 2. Carefully remove the tub from carton. 3. Remove tub from shipping pallet by removing screws from leg mounting pads (Detail“A”). 4. Remove the four screws securing the service access panel (FIGURE 2.1). Side Entry Whirlpool Tub 14 Part No 1118387 SECTION 2—PARTS AND INSTALLATION Service Access Panel Models 3600 and 3600XL Model 3650 Service Access Panel B E D H Right Side of Tub Left Side of Tub Floor Drain C I Rear of Tub A J G F Hot and Cold Water Inlets DETAIL “A” Leg Leg Mounting Pad Screw Screw LETTER DESCRIPTION LENGTH IN INCHES A Work Area Width 75 minimum/96 recommended B Work Area Length 76 minimum/103 to allow lift access C Tub Rear Clearance 3 minimum/30 to allow lift access D Door Swing Clearance 40 minimum E Length of Tub 67 F Tub Front Clearance 6 G Drain Outlet Front to Tub Front 14 H Tub Center to Drain Outlet Center 8 I Tub Width 32 J Right Side Clearance 3 minimum...