Assessments - 6, GPA: 4.5
(
)
)
|
Facilidade de uso
Contact a qualified electrician if there is any question as to the suitability of the system. CAUTION: Make sure the power is off before starting the installation. This fixture can be mounted on a wall with, or without using a flush-mounted junction box. Do not attempt to mount this fixture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application. Installation Using A Junction Box Note: If your junction box protrudes out of the wall slightly, you may want to use the enclosed gasket so less caulking is required. 1. Hold the Mounting Bracket and Gasket over the junction box. Thread the supply wires through the large hole in the back of the Mounting bracket. Select the holes in the mounting bracket that line up with the screw holes in the junction box. Make sure the bottom of the Mounting Bracket is level. Secure with the two #8 screws provided. Installation Without A Junction Box 1. Select a location on a flat wall with structurally sound wood and from 5 to 25 feet from the ground. The wood should be at least one inch thick to safely secure the fixture. 2. Use the Mounting Bracket as a template. Hold it at the desired mounting location (making sure the bottom is level), and mark four mounting holes. 3. Use four #8 or #10 wood screws or galvanized deck screws at least 1 inch long (not provided) to secure the Mounting Bracket to the wall. It may be necessary to drill appropriate pilot holes if mounted to hardwood to avoid splitting. 4. Remove the knockout in the bottom of the Mounting Bracket, and bring your supply wires through this knockout using appropriate flexible conduit or other approved means of wiring. Complete The Installation 1. Put the Temporary Pin through the holes in the Mounting Bracket. 2. This fixture must be grounded. Connect the supply ground wire to the green ground screw. You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected. 3. Slide the fixture onto the Mounting Bracket, and allow the fixture to rest on the Temporary Pin. 4. Connect the fixture wires to the supply wires (black to black, white to white, and if a ground pigtail was added above, connect this pigtail to the supply ground wire). Secure with the wire connectors provided. 5. Remove the Temporary Pin, and slide the fixture all the way down onto the Mounting Bracket making sure no wires get pinched. 6. Install the screw through the bottom of the Mounting Bracket and into the fixture housing. Tighten this screw. 7. Install ONLY a 100 watt mercury vapor type H38 lamp (provided). 8. Caulk fixture mounting surface with silicone weather sealant. To test operation during daylight, cover the photocontrol with black tape. Turn on the power. The light will take up to ten minutes to reach full brightness. Remove the tape from the photocontrol and your unit will operate automatically—on at dusk, off at dawn. Photocontrol Gasket (Optional) MountingBracketGround ScrewFixtureLampTemporary Pin © 2005 DESA Specialty Products™ 598-1059-02 TECHNICAL SERVICE Please call 1-800-858-8501 for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: DESA Specialty Products™ P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service Specialty Products * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product ONE YEAR LIMITED WARRANTYThis is a “Limited Warranty”which gives you specific legal rights.You may also have other rights which vary from state to state or province to province. For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Not Covered -Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty.Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety.This warranty does not include reimbursement for incon- venience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL ...