Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• Automatically turns light off. • Dusk Accent lighting. • Photocell keeps the light off during daylight hours. This package includes: • Lantern • Easy to use universal mounting bracket (X-Bar) • Mounting hardware • Wire nuts Requirements • The Light Control requires 120 volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time Works: Day Night Test 5 Seconds x x Auto 1, 5, or 10 Min x Manual To Dawn* x Accent 3,6 Hr, to Dawn x * resets to Auto Mode at dawn. Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate. TEST Set the ON-TIME switch onthebottomofthe cover plate to TEST.TEST1 5 10 MIN AUTO Set ON-TIME switch to 1, 5, or 10 minutes.TEST 1 5 10 MIN MANUAL MODE 1 Second OFF then... Manualmodeonlyworksat night because daylight re- turns the sensor to AUTO. Flip the light switch off for onesecondthenbackonto toggle between AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position. ... back on. Mode Switching Summary ON-TIME Switch at 1, 5, or 10 minutes Flip light switch off for one second then back on* * If you get confused while switching modes, turn the power off for one minute, then back on.After the calibration time the control will be in the AUTO mode. DUALBRITE® Dimmer Control Light comes on half bright for selected time after dusk (3 hr., 6 hr., until dawn). If motion is sensed, the light turns on full bright for the ON-TIME (1, 5, or 10 minutes) then returns to dim mode. TEST AUTO MANUAL MODE © 2006 DESA Specialty Products™ 595-5628-07 INSTALLATION WIRING For best performance, mountthe fixture about 6 feet (1.8 m) above the ground. WARNING:Turn power off atthecircuit breaker or fuse. . Twist the junction box wires and the fixture wires together as shown below. Secure with wire connectors. If you have a metal junction box, you may not need the green “pigtail”. If you are unsure about the grounding method, consult your local building code. CAUTION: DO NOT connect the RED 1. Remove two nuts. 2. Remove X-Bar. MAXMIN3.Tighten screws finger tight. SENSITIVITY4. Set sensitivity on fixture back to the mid-position. One Motion LightBLACKWHITETwo Motion LightsBLACKBLACKWHITE wire unless you want to control other Junction Box5. Attach X-Bar to junction boxDue to the size and weight of the fixture, you mayfindithelpfultohaveanassistantholdthe fixture in place while connecting the wires. lights from the motion sensor. 2595-5628-07Recommended Grounding MethodUse a green ground “pigtail”(not provided) and twist one end together with the bare fixture wire and the box ground wire.Secure with a wire connector.Secure the other end of the “pigtail” with the GND screw on the X-bar. Black to blackWhite to white OPTIONAL WIRING . When wiring to additional standard fixture only: Strip the motion sensor's red wire and connect to the standard light's black wire. Connect all white wires together. Total fixture ratings must not exceed 360 Watts (3.0 A.). NOTE: All wiring between fixtures should be run in accordance with the National ElectricalCode(CanadianElectrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system. . This fixture is provided with a sensor rated for 360 Watts. Since the fixture is only rated 100 Watts (180 Watts candelabra), 260 Watts (180 Watts candelabra) of additional load may be controlled by this sensor. . When determining what a fixture is rated for, do not simply look at the rating on the lamp in the fixture. Look at the marking which specifies the maximum lamp wattage for which the fixture is suitable. . Once you have selected the fixtures to be connectedanddeterminedtheirmaximum ratings, add these ratings up.For instance, if you have 3 fixtures rated 100 Watts, 150 Watts, and 75Watts respectively, you have a total load of 325 Watts. Master Slave Wiring to Motion Light & Standard FixtureBLACKWHITEBLACK(Standard) REDWHITEBLACKBLACKWiring to Control One Motion Sensing Lan- tern (Slave) from Another (Master) RED It is also possible to wire two motion sensing coach lights so that either unit will turn on both lights at the same time (dual master system). It is recommended that only people with plenty of electrical experience attempt this configuration. Please call our customer service number (1-800-858-8501) before attempting this wiring. If the dual master wiring is not done correctly, it can destroy both motion sensing fixtures and void your warranty. 595-5628-07 3 COMPLETE THE INSTALLATION . Stuff the wires into the junction box. Make Model 4193 Glass Installation sure none of the wires get pinched. Slide the fixture onto the mounting screws and tighten nuts. Junction Box . Install one 100Watt maximumlightbulb,or three 60 Watt bulbs in candelabra style. . Install the fixture top. Secure with decorative screws. . After ...