WSF36 CONTENTS Key Qty. Description A 2 Large Side Grids Back Grid B 1 C 2 Center Grids D 1 Front Grid E 1 Bottom Step F 4 Casters G 1 Bag Small Clips H 1 Bag Large Clips F NOTE: Plastic clips can be snapped on and removed easily by hand. Most grid sections require only 2 clips per side for support. For safety, clips attached on exterior of cart should be positioned with flanges facing inward. (See reverse side for assembly) CLIP ATTACHMENT TAIWAN Assembly Instructions for No

Use care to differentiate the four crossbars from each other, as shown in the parts list. Also use care to differentiate left side frame from right, as shown in the parts list. Attach rear crossbars (B and C), footrest crossbar (E), and front crossbar (D) to one side frame (A) using 2" Allen bolts (G) to one) to one ). Pay close attention to correct orientation of all pre- drilled holes. Tighten securely. Attach other side frame to opposite ends of four crossbars in step two using 2" Allen bolts

Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach both rear crossbars (B) and the footrest and support crossbars (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %

Use care not to drill all the way through the tabletop. ^5 Attach front hinges and rear brackets to tabletop using %" Phillips screws (I). Tighten securely but use care not to over tighten and strip. ©2008 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722 WWW.alvinCO.COm Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896 lit-abiss 7/qb

Pay close attention to correct orientation of left and right hinges. Tighten securely. Insert tilt adjustment rods (F) into threaded barrels on each side frame. Screw adjustment knobs (E) into threaded barrels on each side frame. Set adjustment rods so that connecting brackets are about 2" above side frames for the time being with rods facing straight up and down and rear mounting brackets facing out, as shown in diagram. Tighten knobs securely. Base frame assembly is now complete. Set aside.

Hinges should also be centered evenly between left and right sides of tabletop. ^3 Adjust and position rear mounting brackets so they are 19/" from the front edge of the table top and centered evenly between left and right sides, as shown in diagram. Brackets should sit flush on the tabletop surface with the rods facing straight up and down. ^4 Mark locations of all 12 holes with a dark pencil or marker and then use an awl or drill with 1/i6" bit to make starter holes. Use care not to drill al

Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach both rear crossbars (B) and the footrest and support crossbars (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %

WTF35 B C E CONTENTS Key Qty. Description A 1 Grid Tray with small openings B 1 Frame Section with rubber feet C 2 Grid Tray with large openings D 1 Frame Section E 2 Covered Casters with lock nuts F 2 Side Braces (left and right) G 1 Dust Protector bottom cover (Optional) 12 Nuts, 4 Screws 1. Attach grid tray with small openings(A), to bottom of large frame section(B). 2. Attach remaining two trays(C). 3. Secure smaller frame section(D) in the same manner. 4. Using encl

For best results, we suggest that you tighten the four Allen bolts in sides of main easel frame, as shown in Figure 1, and tighten the two Phillips screws in the back of canvas support assembly, as shown in Figure 2. 2 Lay main easel frame flat on floor with brass height adjustment track facing up. □ Carefully slide canvas support assembly from below into slots and tracks in main frame, as shown in Figure 3. Pull spring-loaded height-adjustment ring and set in the third track position for th

Make sure ends of back panel are snug against steel leg frames and holes are aligned in steel flange with pre-drilled holes in back panel. Attach using four 5/s" screws (I) supplied. Repeat step for right leg frame. Figure 2 5/s" Screws Floor Glide Figure 1 5/s" Screws □ Carefully remove base assembly from table/bench and place upright on floor. ^9 Place shelf (D) with predrilled holes facing up on the bench/table with 15 ends hanging over edge. Lift base assembly carefully (may require