Brick (B Models) Rear Refractory, Std. Brick (B Models) Bottom Front Refractory, Std. Brick Bottom Rear Refractory, Std. Brick Firebox Support Leg Box Assembly Screen Rod Firebox Top Assembly Screw, #10x5/8 Mod. Tr. Blk. Ox Damper Door Assembly Firebox Face Smoke Deflector Fireplace Top Insulation Grate Assembly Burner Assembly Burner Pan Burner Tube Burner Bracket Pilot Shield Burner Clamp Nut, #10-24 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 1 2 1 1 1 1 1 1111111 24-10 24-11 24-12 25 26 27 28 29 30 31 3

This hearth extension may be either minimum 6-inch thick stone or brick as shown by Figure 10, an H2066 Hearth Extension Kit or a locally constructed hearth equivalent to the H2066. The insulation used in the H2066 hearth extension has a thermal conductivity (K Factor) of .43. If you do construct a hearth extension equivalent to the H2066, be sure the insulation you use has enough compressive strength to support the weight of the covering materials and persons standing on it, and insulating qual

14. Turn on all electrical power to the fireplace. 3/8" - 1/2" FP1068Lighting instructionsPilots PILOTONOFFONPILOTOFFOFFFP1067lighting instructionknobs3/9/01 djt54321OFFPilot Honeywell SIT NOVA Euro SIT To Turn Off Gas to Heater 1. Turn the On/Off switch to "Off" position or set the thermostat to lowest setting. 2. Turn off all electric power to the fireplace if service is to be performed. 3. Open control access panel. 4. Push in gas control knob slightly and turn clockwise to "OFF". Do not forc

Orange flame will also be present. Open window to vent smell. This will only last a few hours. 1. STOP! Read the safety information, column 1. 2. Set the thermostat to lowest setting (if applicable). 3. Turn off wall switch. 4. Open control access panel or louver. 5. Smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information in column 1. If you don’t smell gas, go to the next step. 6. Turn the main burner wall switch to the ON position for ignition. The

To help prevent the crack from developing, the hearth extension materials must be firmly fastened in place. Wall ties should be screwed to the face of the fireplace and imbedded in the mortar joints of brick, stone, or other noncombustible materials. The metal safety strip packed with the fireplace must be placed beneath the fireplace and extended under the hearth extension or into a mortar joint of the hearth extension as shown by Figures 10, 11, and 12. In the event a crack does eventually dev

The clearances are the same for either installation method. Mantel Clearances for Built-In Installation If placing custom mantel above built-in firebox, you must meet the minimum allowable clearance between mantel shelf and top of firebox opening shown in Figure 7. These are the minimum allowable mantel clearances for a safe installation. Use larger clearances wherever possible to minimize the heating of objects and materials placed on the mantel. A CAUTION: Do not allow the vent-free gas log

Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer, service agency or the gas supplier. INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. For more information, visit ik WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct i

The flue outlet must be a minimum of three feet above the point where in penetrates the roof. Figure 14. CAUTION: Be careful to avoid electrical shock hazard when contacting wires to the metal chimney components. 1. Extend the regular chimney sections until the top of the chimney is 4 inches below the total flue height desired. Do not snap the last section of inlet air duct or largest diameter pipe in place until Step 3 is completed. 2. Remove the shingles from around the chimney so that the fla

This will prevent the entry of cold air by means of conduction through the total bottom of the appliance. (see Figure 32). CAUTION: Air inlet ducts are not to terminate in attic space. Note: Glass door may be heavy for some individuals. If this is the case, please request help from someone else. The M36E, VM36E, M42E and VM42E B-vent fireplaces are approved for use with optional bi-fold glass doors (see Accessories, page 27). The glass panels may be ordered and installed anytime after the firepl

If damaged, promptly inform dealer or distributor where you bought the product. Safely retain these items for later installation. For more information, visit more information, visit 108796-01E 4 4 INTRODUCTION Before You Begin INTRODUCTION Models M36E(B,H), VM36E(B,H), M42E(B,H) and VM42E(B,H) are vented gas fireplaces that use an electronic gas control valve and electronic ignition system. A 6" B-Type venting system and a listed type vent cap are not supplied but are required for proper operati