Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
B A C D M H I G K L E F Figure 8. Dust Collector Inventory. J N O P F. Separator Supports • Phlp Hd Scr M6-1 X 12 (16) G. 6" to 4" Inlet Y • Hex Wrench 4mm (1) H. Dust Collection Bags • Hex Wrench 5mm (1) I. Gasket P. Small Bolt Bag: J. Casters • Hex Bolt M8-1.25 X 16 (12) K. Bag Clamps • Hex Bolt M8-1.25 X 25 (4) L. Hose Clamps • Flat Washer 8mm (20) M. Wrenches • Hex Nut M8-1.25 (4) N. Outlet UNPLUG the power cord before you do any assembly or adjustment tasks! Otherwise electrocution may occur! -12 W1666, W1685 Dust Collectors Casters and Motor For quiet and vibration-free operation, assemble your dust collector as outlined below. DO NOT modify this dust collector for any other purpose than what it is designed for. To install the casters and motor/impeller assembly, do these steps: 1. MAKE SURE THE DUST COLLECTOR MOTOR IS UNPLUGGED! 2. Install the four swivel casters to the base plate with the sixteen M6-1 X 12 Phillip head screws, washers, and nuts (see Figure 9). GET assistance when lifting machine parts. The SHOP FOX® Model W1666 and W1685 dust collector motor/impeller assembly is heavy, and ignoring this warning can cause you a severe back injury. Figure 9. Caster installation. 3. Bolt the motor to the motor mount with the four M8-1.25 X 25 hex bolts, washers, and nuts; and with lifting assistance, position the motor/impeller assembly on the base (see Figure 10). 4. Secure the motor/impeller assembly to the base using six M8-1.25 X 16 hex bolts, washers, and nuts (see Figure 11). Figure 10. Motor/impeller assembly posi- tioning. Motor Mount Figure 11. Motor/impeller assembly installation. SETUP -13 W1666, W1685 Dust Collectors Outlet, Gasket, and Separator Supports SETUP The outlet directs the dust to the collector hat is supported by three separator support rods. Make sure that you do not overtighten the bolts or the threaded holes in the base can strip. To install the outlet and the separator supports, do these steps: 1. MAKE SURE THE DUST COLLECTOR MOTOR IS UNPLUGGED! 2. Place gasket on top of impeller housing body and place the outlet on the gasket (see Figure 12). 3. Secure the outlet with eight M8-1.25 X 16 hex bolts and flat washers. DO NOT overtighten the bolts or the gasket will squeeze out and the outlet will crack. 4. Place a collector support over one of the sets of holes indicated in Figure 13, and make sure the tail at the top is oriented towards the inside as shown in Figure 14. 5. Secure the three collector supports in place with six M8-1.25 X 16 hex bolts and flat washers. Figure 12. Placing the outlet on the gasket. Figure 13. Separator support bolt locations. Figure 14. Orientation of separator sup- port tails. -14 W1666, W1685 Dust Collectors Separator and Transfer Hose Never bypass the dust collector or and duct the transfer hose outside without using dust collection bags, or move the separator to a remote location and use a longer transfer hose. Any modification can damage the dust collector motor and create an unsafe condition. To install the separator and transfer hose, do these steps: 1. The separator has three tabs with threaded holes along the bottom edge for mounting. Orient the separator so the holes align with supports and the inlet is pointed toward the separator body. See Figure 15. 2. Secure the front and back supports using the hex bolts and washers provided. 3. Secure the upper bag support rod and the last separator support to the separator as in Figure 16. 4. Slide a wire hose clamp onto the end of the transfer hose. 5. Slide the transfer hose end over the inlet for the collector making sure the end passes the ridge on the inlet by 11.2". 6. Position hose clamp over the hose and the inlet making sure the clamp is 3.4" from the end of the hose and tighten the screw on the clamp (see Figure 17). 7. Slide the second hose clamp onto the free end of the hose. 8. Slide the end of the transfer hose onto the outlet of the impeller housing. The hose should go on as far as possible. 9. Slide the hose clamp within 3.4" of the end of hose, and tighten the screw on the clamp. Figure 15. Separator in correct position. Figure 16. Installing upper bag support. Figure 17. Securing transfer hose with clamp. SETUP -15 W1666, W1685 Dust Collectors Dust Bags and Inlet Y SETUP Two dust collection bags are included with your new SHOP FOX® Dust Collector. There is a top and a bottom bag. The top is distinguished by a SHOP FOX® logo. Both bags are secured with band clamps. For increased filtration, optional 0.3 micron dust collector bags are available through your dealer. To install the dust bags and the inlet Y, do these steps: 1. Find the opening in the rim of both bags and insert the band clamps into the rim of the bags until they come out of the other side (see Figure 18). 2. Hang the upper bag as shown in Figure 19. NOTE: The upper bag has the SHOP FOX® logo on it and the lower bag is plain. 3. Position the rim of the upper bag onto the collector and latch the band clamp closed. 4. Po...
Este manual também é adequado para os modelos :Outras ferramentas - W1685 (3.39 mb)