Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Install four casters to the under side of the base as pictured in Fig. 2. Referring to Figure 1: 2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B) against the base with a 14mm wrench. This will give the caster proper clearance. Motor and Fan Assembly Referring to Figure 2: 3. Place the base (C) with casters on the ground. Attach the motor and fan assembly (A) to the base using four each M8 x 16 hex cap screws, and M8 flat washers (B). Tighten with a 13mm wrench. The dust collector must not be connected to the power source during assembly. Failure to comply may result in serious injury! Referring to Figure 3: 4. Attach impeller cover (A) to fan housing (D) using eight M6 x 12 pan head screws (B). Press the inlet ports (C) onto the inlet guard until it snaps into place. To reduce the risk of injury from moving parts, always keep inlet port covered with the caps provided, if they are not connected to a hose. Failure to comply may result in serious injury! Connector Housing 5. Attach three support legs (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. 9 Figure 1 Figure 2 Figure 3 Figure 4 6. Install the housing (A, Fig. 5) to two support legs (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. Note: For models DC-1200BK or DC-1200-3BK only – Before attaching third support bracket place the hanger bracket (D, Fig.5) between the support bracket and the housing. 7. Tighten all nuts and bolts at this time with a 13mm wrench. Figure 5 Cone Assembly Referring to Figure 6: 8. Mount the cone support bracket (E) to the housing with four M6x12 hex cap screws (F), and tighten from beneath with four M6 hex nuts (G). 9. Install the cone (H) from beneath using the M8x16 hex cap screw (J), M8 flat washer (K), and M8 hex nut (L), and tighten. Hose Referring to Figure 7: 10. Attach the hose (B) between the fan housing (A) and the impeller housing (D) with two clamps (C). Tighten the clamps to secure the hose. This completes the Base Unit assembly. If you purchased the DC-1200BK or DC-1200BK-3 Dust Collector (filter bag version), continue on the following page. If you purchased the DC-1200CK or DC1200CK- 3 Dust Collector (canister filter version), proceed to Canister Kit Assembly section on page 12. Figure 6 Figure 7 10 Filter Bag Kit Assembly y If you purchased Model DC-1200BK or DC-1200BK-3 Dust Collector, this section describes the assembly and installation of the contents of the 30 Micron Filter Bag Kit (SN 708636F). These instructions also apply to the optional 5 Micron Filter Bag Kit (SN 708636MF). Filter Bag Installation Referring to Figure 8: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Feed the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). Figure 8 Collector Bag Installation Referring to Figure 9: 4. Insert the ring of the collector bag (A) at an angle into the housing (B) through the opening at the bottom. Pull down on the bag to make sure it “seats” in the housing. 5. Position the plastic window in front so that you can easily see when the collector bag is full. After completing the filter bag and collector bag installation, proceed to Electrical Connections. Figure 9 11 Canister Kit Assembly t Assembly If you purchased Model DC-1200CK or DC-1200CK-3 Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708636F). Canister Filter 1. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 10). 2. Mount the canister filter on top of the collector housing (A, Fig. 5) and tighten the knobs on the canister filter (Figure 10). Figure 10 Collector Bag 3. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 11. Figure 11 4. Insert the snap ring (A, Fig. 12) of the collector bag into the bottom of the housing at an angle. 5. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the snap ring “snaps” into place in the housing, and also that the plastic bag hangs down approximately 3” so that there are no air leaks. 12 Figure 12 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in serious injury! The DC-1200BK/CK dust collectors are rated at 230V Only. The DC-1200 is not supplied with a plug. Use a plug and outlet rated at least 20 amps. The circuit for the machine should also be protected by at least a 20 amp circuit brea...