Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
4. Thread hex nut (B) Fig. 4 onto each of the four bolts and tighten securely. ASSEMBLING SIDE SUPPORTS 1. Place the dust collector base (A) Fig. 5, in an upright position as shown. 2. Align the two holes in the bottom of side support (B) Fig. 5 with the two holes (A) in the base. 3. Insert a 5/16-18x3/4" hex head screw (A) Fig. 6 thru each hole in the side support and base. 4. Place a 5/16" lockwasher onto the hex head screw. 5. Thread a 5/16" hex nut onto the hex head screw and tighten securely. 6. Repeat this process for the remaining side support. A Fig. 3 A B Fig. 4 B A Fig. 5 7. Fig. 7 shows both side supports (A) attached to the base (B). A A A B Fig. 6 Fig. 7 5 ATTACHING MOTOR AND BLOWER ASSEMBLY TO FRAME 1. Place motor assembly and base assembly on their side. 2. Align the four holes, two shown at (C), on the top of the side supports (A) Fig. 8, with the four holes in the motor assembly (B). 3. Place a 5/16" lockwasher onto a 5/16-18x3/4" hex A A B C Fig. 8 head screw and insert the bolt thru the side support and thread bolt into the tapped hole in the motor assembly. 4. Repeat this process for the three remaining holes. 5. Fig. 9 shows the motor and blower assembly attached to the side supports. ASSEMBLING FIRM BOARD 1. Place the firm board (A) inside the two side supports (B) Fig. 10. NOTE: MAKE SURE FIRM BOARD IS ATTACHED TO THE SIDE SUPPORTS CLOSEST TO THE MOTOR. 2. Align the four holes in the firm board with the four holes in the side boards as shown in Fig. 10. 3. Insert a 5/16-18x3/4" hex head screw (A) Fig. 11, thru the side supports and the firm board. 4. Place a 5/16" lockwasher on the hex head screw. 5. Thread a 5/16" hex nut on the hex head screw and tighten securely. 6. Repeat this process for the three remaining holes for attaching the firm board. 7. Fig. 12 shows the firm board attached to the side supports. Fig. 9 AB B Fig. 10 A Fig. 11 Fig. 12 6 ASSEMBLING FILTER AND DUST COLLECTION BAGS TO DRUM 1. Thread a 5/16" hex nut (A) Fig. 13, onto the end of bag support rod (B). Thread rod into hole (E) and tighten nut (A) against motor assembly to hold support rod (B) upright. Height of support rod can be adjusted after the filter bag is in place. The hook in the support rod (B) should be positioned over the drum. AB E Fig. 13 2. Hook the loop on the top of filter bag (F) Fig. 14, onto the end of support rod (B). 3. Position open end of filter bag (F) Fig. 15, over the lip of drum (G). NOTE: It may be necessary to adjust the height of the drum support rod at this time. If adjustment is necessary, loosen nut (A) Fig. 13, and rotate support rod (B) as needed to obtain proper rod height to support filter bag (F). Tighten nut (A) Fig. 13. Place locking band (H) around the filter bag (F) and fasten filter bag to drum by locking clamp (J) as shown in Fig. 15. IMPORTANT: Make certain band (H) is positioned in the channel of drum (G) before locking clamp (J). 4. Place the remaining locking band (H) Fig. 16, around the dust collection bag (K). Position open end of bag over the lip of drum (G) and fasten with locking clamp (J). NOTE: Make certain locking band (H) is positioned in the channel of drum before locking clamp (J). 7 F B Fig. 14 JH G F Fig. 15 H G K J Fig. 16 ASSEMBLING DUST INTAKE HOSE TO MOTOR AND BLOWER ASSEMBLY The dust collector is supplied with a 4" flexible dust intake hose. Place the intake cap holder (E) on the dust collector as shown in Fig. 17. NOTE: DO NOT COVER THE INTAKE PORT WITH THE INTAKE CAP WHEN ATTACHING THE HOSE TO THE INTAKE PORT. To assemble the dust collection hose to the motor and blower assembly, loosely attach hose clamp (A) Fig. 17, around one end of flexible hose (B) and assemble the hose to dust intake port (C). Tighten hose clamp (A) Fig. 18. Assemble the remaining clamp to the other end of the flexible hose and to the woodworking machine. IMPORTANT: Do not operate the dust collector without the flexible hose assembled to the dust intake port. Always disconnect dust collector from the power source before connecting or disconnecting an air intake hose to or from the blower and motor assembly. E A C Fig. 17 A B D Fig. 18 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and 3-hole receptacles which accept the tool’s plug. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the tool. All line connections should make good contact. Running on low voltage will damage the motor. MOTOR SPECIFICATIONS Your tool is wired for 120 volt, 60 HZ alternating current. Before connecting the tool to the power source, make sure the switch is in the “OFF” position. GROUNDING INSTRUCTIONS WARNING: THI...