Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Replace if torn or perforated or when plugged to maintain proper carburetor setting (50 hours). DO NOT WASH IN ANY LIQUID AND DO NOT OIL. Paper Element Element 'Attaching Screw FIGURE 19 CARBURETOR ADJUSTMENTS (See figure 20) Do not make unnecessary adjustment. Factory settings are correct for most application. If adjustments are needed, proceed as follows: 1. Close power adjusting needle (figure 20) by turning to right (clockwise). Close finger tight only. Forcing will cause damage. 2. Open one turn (counterclockwise). 3. Close idle adjusting needle (figure 20) by turning to right (clockwise). Close finger tight only. Forcing will cause damage. 4. Open one and one-half (1 1/2) turns (counterclockwise). 5. Start engine. Follow starting instructions page 4— 6. With throttle open (carburetor control at RUN FAST position) adjust power adjusting needle one-eighth (1/8) turn at a time forward or backward until engine runs smoothly. If engine tends to stall under load enrich mixture slightly (counterclockwise). 7. Hold throttle lever closed or move carburetor control to IDLE or SLOW position and adjust idle adjusting needle until engine runs smoothly proceeding in step six (6) above. . Allow several seconds between each adjustment when performing either step six (6) or seven (7) to allow engine to react to new setting. FIGURE 20 STORAGE INSTRUCTIONS In event engine is to be stored for any length of time (30 days or more), prepare as follows: 1. Drain gasoline by tipping or by syphon hose, then run engine until remainder is used and tank and carburetor are empty. CAUTION Drain into container outdoors away from fire or flame. 2. Drain carburetor by running engine until it stops. 3. Inside protection of engine for storage is performed by removing spark plug and pouring one ounce of SAE 30 oil through spark plug hole into cylinder. Crank engine, without starting, several times to spread oil over cylinder walls. 4. Never store outside without a waterproof cover. 9 \ 047-6*°* 24640-7 10 /-*"^RTS LIST FOR LOG SPLITTER MODELS 247-640A and 24640-7 ..ef. No. Part No. Color Code Description New Part Ref. No. Part No. Color Code Description New Part 1 710-0331 HexScr. 3/8-24x2.25” Lg.* 25 13291 Engagement Lever Ass’y. N 2 13275 Cam Plate N 26 738-0258 Shoulder Scr. 3/8-16 Thd. 3 727-0203 High Pressure Hose Ass'y. 27 13280 Strainer Tube Ass'y. N 11.0" Lg. N 28 727-0204 Return Hose N 4 737-0155 Reducing Bushing N 29 711-0169 Collar 5 717-0364 Valve N 30 734-0584 Wheel Ass’y. Comp. 6 736-0119 L.-Wash. 3/8'’ Scr.* 31 736-0237 FI.-Wash. .656 I.D.x 1.00Th d. 7 712-0241 Hex Nut 3/8-24 Thd.* 32 13276 Tank Ass’y. Complete N 8 08118 Grip 33 751-0224 Breather Cap N 9 737-0153 Return Elbow N 34 727-0205 Inlet Hose N 10 737-0154 Cylinder nipple .75,rx4.5” Lg . N 35 737-0151 Inlet Nipple N 11 732-0342 Spring Clip N 36 717-0363 Pump - Comp 1 ete(wEGSTEfc) N 12 732-Q341 Cylinder Return Spring N 37 737-0152 High Pressure Elbow N 13 13304 Cylinder Ass’y. N 38 710-0376 Hex Scr. 5/16-18X 1.00" Lg * 14 721-0159 “0”-Ring N 39 712-0267 HexNut5/16-18 Thd.* 15 13302 Push Cylinder Ass’y. N 40 13295 Coupl ing Support Brkt. Ass’} . N 13314 Spring Hook Ass’y. N 41 714-0114 Sq. Key 1/4" x2.00” Lg.* 7 726-0173 Hose Clamp N 42 710-0237 Hex Scr. 5/16-24x .62” Lg.* 18 749-0251 Engagement Handle N 43 710-0528 Hex Scr. 5/16-18x1,25”Lg. * 19 13310 Cylinder Holding Plate N 44 Engine 20 736-0119 L-Wash. 5/16” Scr.* 45 717-0374 Flexible Coupling Comp. N 21 710-0528 Hex Scr. 5/16-18x1.25” Lg. 46 714-0507 Cotter Pin 3/32” Dia. x .75” Lg.* 22 13305 ‘T’-Beam Ass’y. Comp. N 47 736-0142 F I.-Wash. .281 .D. x .50” O.C ). 23 13312 Return Collar Ass’y. N 48 711-0660 Clevis Pin N 24 710-0494 Sq. Hd. Set Scr. 5/16-18X .38” Lg. / ‘For faster service obtain standard nuts, bolts and washers locally. If these Items cannot be obtained locally, order by part number and size as shown on parts list. The engine is not under warranty by the log splitter manufacturer. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the "Yellow Pages” of your telephone book under ‘‘Engines — Gasoline.” Find It Fast In The Yellow Pages 11 PARTS INFORMATION POWER EQUIPMENT PARTS AND SERVICE Ports and service for all MTD manufactured power equipment are available through the authorized service firms listed below. All orders should specify the model number of your unit, parts numbers, description of parts and the quantity of each part required. ALABAMA BIRMINGHAM Auto Electric & Carburetor Co...2625 4th Ave. S........ 35233 ARKANSAS NORTH LITTLE ROCK Sutton's Lawn Mower Shop .....Rt. 4, Box 368 ......... 72117 FORT SMITH Mity Mite Motors, Inc: ...........2515 Towson Ave..... 72901 CALIFORNIA SAN BERNARDINO Lawn Mower Supply Co......... 25608 E. Baseline .... 92410 SAN FRANCISCO J.W. Jewett Co..........