Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Never place hands or feet between log and splitting wedge or between log and push plate while operating. To do so may result in crushed or amputated fingers or toes, or worse, you may lose an arm or foot. 2. Do not straddle the splitter when using it. A slip in any position could result in a serious injury. 3. Never try to split two logs on top of each other. One may fly out and injure you. 4. Only use your hand to operate the ram or control lever. Never use your foot or a rope or any other extension device. This could result in your inability to stop your splitter quickly enough and cause an injury. 5. Always keep fingers away from any cracks that open in the log during splitting operation. They can quickly close and pinch or amputate your fingers. 6. Never attempt to split wood across the grain. Some types of wood may burst or fly out of your splitter and result in injury to you or a bystander. 7. For logs that are not cut square, the longest portion of the log should be rotated down and the most square end placed against the ram. 8. Keep your work area clean. Immediately remove split wood around your splitter so that you do not stumble over it. MAINTENANCE AND STORAGE 1. Do not operate your splitter in poor mechanical condition or when in need of repair. 3 I 2. Periodically check that all nuts, bolts and screws are tight to be sure equipment is in s.jfe working condition. Where appropriate, check all safety guards and shields to be sure they are in the proper position. Never operate your splitter with safety guards, shields or other protective features removed. These safety devices are for your protection. 3. Replace all damaged or worn parts such as immediately with manufacturer approved replacement parts. 4. Do not alter your splitter in any manner such as attaching a rope or extension to the control lever or adding to the width or height of the wedge. Such alterations may cause your splitter to be unsafe. 5. Perform all recommended maintenance prc cedures before you use your splitter. 6. Never store log splitter outside without a waterproof cover. Rain will cause rust on the inside of the cylinder. 4 - F- FIGURE 1 ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK AND LOOSE PARTS: (See Figure 1) A (1) Handle Grip B (1) Handle C (1) Hairpin Cotter (may be rings) D (1) Clevis Pin (may be pin) E (1) Axle F (2) Push on caps 1/2" Dia. G (2) Spacers H (2) Wheels WELDED TUBE WHEEL (H) \ 1. Remove the log splitter, loose parts and literature from carton. Check to be sure all parts are removed from carton before discarding the carton. 2. Place the axle (E) through the welded tube on splitter. See figure 2. 3. Next, place spacers (G) on each side of splitter, over axle. See figure 2. PUSH ON CAP (F) FIGURE 2 USE A SECOND HAMMER, OR BLOCK OF WOOD 4. Next, place wheels (H) over each end of axle* See figure 3. 5. Secure wheels to axle with push on caps (F). A hammer and block of wood will be required to hammer on the caps. See figures 2 and 3. HAMMER FIGURE 3 5 I 5. Lift the handle socket up so that the hole lines up _ with the hole in plunger shaft. See figure 4. 6. Secure handle socket to plunger shaft with hair pin (C) and clevis pin (D). See figure 4. 7. Place the handle grip (A) over one end of handle (B). Warm soapy water will aid in assembly. Tap grip on. 8. Place handle over handle socket. FIGURE 4 HANDLE ON CYLINDER MOUNTING ASSEMBLY OPERATION This 8 ton capacity hydraulic unit is a special design, manufactured for use on this log splitter only. 1. This splitter can be adjusted manually for logs 8" to 24" long. There are twelve different settings. Settings are approximately 1-1/2" apart. See. figure 5. 2. Simply lift up on handle of cylinder mountinc, assembly and slide the unit forward or backward for the correct log length. See figure 5. FIGURE 5 3. Pull the release valve up and back to lock. Then handle can be pumped to split logs. See figure 6. FIGURE 6 6 4. Push the release valve down and forward to release pressure. Cylinder will return, with the aid of two return springs. See figure 7 and copy of label below. DOWN TO S A UP TO LOCK RELEASE / / PUMP AND PRESSURE -y SPL,T --— —5052 FIGURE 7 CYLINDER RESERVOIR SCREW AND WASHER MAINTENANCE RESERVOIR OIL 1. SCREWDRIVER HANDLE HANDLE FIGURE 8 Lift the handle on the cylinder mounting assembly and pull cylinder assembly all the way back to the last notch. See figure 8. 2. Remove the pump handle. 3. Release the pressure in the cylinder. 4. Tip the log splitter up so it rests on the wheels and handle on cylinder assembly. See figure 8. 5. With a standard screwdriver, remove screw and washer from cylinder reservoir. See figure 8. If oil is up to hole, do not add any oil. If not, add oil to bring level up to hole. Oil capacity is 10 fluid ounces. Nuto H grade 32, or Exxon L.P. conventional #150 Hydraulic oil. 7 I 8 Model 632 PARTS LIST FOR MODEL 632 LOG SPLITTER PART NO. QUAN. DESCR...