Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Work that is apt to splinter should be backed up with a block of wood. Keyed Chuck (Fig. 1, 3, 4) The DWD010 and the DWD014 feature a keyed chuck (d). FIG. 3 FIG. 4 TO INSERT A DRILL BIT OR OTHER ACCESSORY 1. Open the chuck jaws by turning collar by hand and insert the shank of the bit about 19 mm (3/4") into chuck. Tighten the chuck collar by hand. 2. Place chuck key in each of the three holes, and tighten in clockwise direction. It’s important to tighten chuck with all three holes. To release the bit, turn the chuck counterclockwise in just one hole, then loosen the chuck by hand. REMOVAL OF KEYED CHUCK (FIG. 3) Tighten the chuck around the shorter end of a hex key. Using a soft hammer, strike the key sharply in the counterclockwise direction when viewed from the front of the tool. This will loosen the chuck so that it can be removed by hand. 6 English English English KEYED CHUCK INSTALLATION (FIG. 4) Screw the chuck on by hand as far as it will go. Insert the shorter end of a hex key and strike it in the clockwise direction with a soft hammer. MAINTENANCE Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. WARNING: To reduce the risk of injury, turn unit off and disconnect tool from power source before installing and removing accessories, before making any adjustments or removing/installing attachments or accessories. Motor Brushes DEWALT uses an advanced brush system which automatically stops the drill when the brushes wear out. This prevents serious damage to the motor. New brush assemblies are available at authorized DEWALT service centers. Always use identical replacement parts. Lubrication Self-lubricating bearings are used in the tool and periodic relubrication is not required. In the unlikely event that service is ever needed, take your tool to an authorized service location. Cleaning WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. 7 Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. CAUTION: To reduce the risk of injury, the following accessories should be used only in sizes up to the maximums shown in the table below. MAXIMUM RECOMMENDED CAPACITIES DWD010 DWD014 CHUCK CAPACITY 6.5 mm 10 mm BITS, METAL DRILLING 6.5 mm 10 mm WOOD, FLAT BORING 15 mm 25 mm SPECIFICATIONS DWD010-B3 DWD014-B3 Voltage 120 V~ 120 V~ Frequency 50-60 Hz 50-60 Hz Power - watts 380 W 600 W RPM 0–3600 0–2800 Definiciones: Normas de seguridad Las siguientes definiciones describen el nivel de gravedad de cada advertencia. Lea el manual y preste atencion a estos simbolos. PELIGRO: Indica una situacion de peligro inminente que, si no se evita, provocara la muerte o lesiones graves. ADVERTENCIA: Indica una situacion de peligro potencial que, si no se evita, podria provocar la muerte o lesiones graves ATENCION: Indica una situacion de peligro potencial que, si no se evita, puede provocar lesiones leves o moderadas. AVISO: Se refiere a una practica no relacionada a lesiones corporales que de no evitarse puede resultar en danos a la propiedad. ADVERTENCIA: para reducir el riesgo de lesiones, lea el manual de instrucciones. Advertencias generales de seguridad para las herramientas electricas ADVERTENCIA: Lea todas las advertencias de seguridad e instrucciones. El incumplimiento de las advertencias o instrucciones puede provocar descargas electricas, incendios o lesiones graves. GUARDE LAS ADVERTENCIAS E INSTRUCCIONES PARA PODER CONSULTARLAS EN EL FUTURO El termino “herramienta electrica” incluido en todas las advertencias se refiere a su herramienta electrica conectada a la red (cable electrico) o a su herramienta electrica accionada con baterias (inalambrica). 8 1) SEGURIDAD DEL AREA DE TRABAJO a) Mantenga el area de trabajo limpia y bien iluminada. Las areas abarrotadas u oscuras propician accidentes. b) No haga funcionar las herramientas electricas en atmosferas explosivas, como ambientes donde haya polvo, gases o liquidos inflamables. Las herramientas electricas originan chispas que pueden encender el polvo o producir humo. c) Mantenga alejados a los ninos y a los espectadores ...
Este manual também é adequado para os modelos :Outras ferramentas - DWD010 (3.89 mb)