Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Any part that is damaged should be properly repaired or replaced by a qualified technician. Replacement parts and accessories7. . When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this product. Do not excessively overload the 8. shelves. Never use the Hanging Cabinet as a 9. seat, a stool or a ladder. Use eye protection10. . Wear ANSI- approved impact safety goggles when assembling. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. REV 01i, 04c Assembly Your Hanging Tool Cabinet, will require complete assembly as described in the following steps. To assist you with assembly and operation, please refer to the Operational Figures as well as the Parts List and Assembly Diagram located on the last pages of this manual. Figure 1-Attaching Bottom Panel to Right Side PanelLipRight Side Panel (#7) Bottom Panel (#12) Bolts (#6) 1. Lay out the Bottom Panel (part #12) on your work area with the Lip facing toward what will be the front of the Hanging Tool Cabinet. Attach the Right Side Panel (#7) to the Bottom Panel (#12) making certain that the lip faces the front of the Hanging Cabinet. The lip should line up with the lip of the Bottom Panel (#12)-see Figure 1. Insert two (2) Bolts (#6) up through the Bottom Panel (#12) then thread the Nut (#5) onto the Bolt (#6). Repeat for the Left Side Panel (#16). 2. Set the Hanging Tool Cabinet so that the Back Panel (#8) will be supported against a workbench, wall or floor. Lay the edge of one (1) Back Panel (#8) inside and at the rear of the Bottom Panel (#12)-see Figure 2. Repeat for the remaining two (2) Back Panels (#8). The Center Panel 2 (#3) has a split/double lip-3. see Figure 3, next page. Set Center Panel 2 (#3) so that the split lip faces the front of the Hanging Cabinet. The back edge of Center Panel 2 (#3) will lay on the edge of the rear right Back Panel (#8). Insert one Bolt (#6) through each hole in the edge of the right 4. Back Panel (#8), through the holes in the Center Panel 2 (#3) and through the holes in the middle Back Panel (#8). Thread Nut (#5) onto Bolt (#6). Note: Back Panels (8) do not bolt to Side Panels (7 & 16) directly, Back Panels (8) only bolt together and to the Top and Bottom Panels (1 & 12). Set the Center Panel 1 (#2) so that the lip faces front and the rear edge sits against 5. the back of the Bottom Panel (#12). Insert one Bolt (#6) through each hole in the edge of the left Back Panel, through the holes in the Center Panel 1 (#2) and through the holes in the middle Back Panel (#8). Thread Nut (#5) onto Bolt (#6). Figure 2Back Panel (#8) REV 01i Note: Each Door is labeled indicating Right Door, Left Door, and Center Door. Loosely set the Top Panel (#1) in place on top of the assembly you finished in steps 6. one (1) through five (5) above. Make certain that the lip faces the front of the Hanging Cabinet. Insert the Right Door (#11) into the holes in the Top and Bottom Panel. The Doors are attached with pins which set into holes; make certain to lay the Washer (hardware bag) over the pin prior to insertion. Insert the Center Door (#13) into the holes in the Top and Bottom Panel. Repeat for the Left Door (#15). Once the Doors are in place, attach the Top Panel (#1) to the assembly by inserting 7. two (2) Bolts (#6) down into the Right Side Panel (#7) and two Bolts (#6) down into the Left Side Panel (#16). Secure in place with Nuts (#5). Thread in remaining three (3) Bolts (#6) through the Top Panel (#1) and into Center Panel 1(#2) and Center Panel 2 (#3), and into center Back Panel (#8). Secure with Nuts (#5). Figure 3-Center PanelFigure 4-Inserting LockKeyWashersScrewLeverLarge Nut 8. Remove the large Nut off of the Lock (#14). Force the Lock (#14) into the hole in the Right Door (#11). Thread the large Nut back onto the Lock until it rests against the Door, securing the Lock (#14) in place-see Figure 4. Remove the washer and star- shaped lock washer from the Lock by loosening the screw on the end-see Figure 4. Slip on the locking lever so that when the key is turned the lever is horizontal, and then replace the washer and lock washer onto the Lock (#14)-see Figure 4 above. Repeat for the remaining two (2) Locks (#14). Note: Each Lock (#14) comes with two (2) keys. Turning the key should move the lever to a horizontal position which will keep the Door from opening. To hang the Cabinet, attach the two (2) Hangers (#4) to the right and left sides of 9. the Back Panel (#8) with two (2) Bolts (#6). The Hangers (#4) should be attached to the Back Panel (#8) at different ends of the Cabinet so that when hung the weight is evenly distributed. Hang the Cabinet with the one (1) hole in each Hanger. ...