Assessments - 3, GPA: 3 ( )

Fabricante : Lennox Hearth Arquivo Tamanho: 1.74 mb Arquivo Nome : Língua de Ensino:

• The 30" log set also includes 2 ember chunks (shown in Figure 18b) * Figure 10 - Log Set Figure 9 Note: Diagrams aND illustratioNs are Not to scale. 10 Note: Diagrams aND illustratioNs are Not to scale. LOG PLACEMENT INSTRUCTIONS 1. Place rear ember bed as shown in Figure 11. Figure 11 - Install Rear Ember Bed 2. Place rear log onto the two rear grate locating pins as shown in Figure 12 (the locating pins are outlined in Figure 11). 3. Place middle log onto left middle grate locating pin and the rear ember bed locating pin as shown in Figure 13. Middle Log Locating Pins 4. Place left and right front logs onto front grate locating pins as shown in Figure 14. Figure 12 - Install Rear Log Figure 13 - Install Middle Log Figure 14 - Install Left and Right Front Logs Install Ember bed from behind top burner Top Burner Rear Ember Bed Position Ember Bed All the Way Forward in Gas Train Assembly Locating Pins Rear Log Rear Locating PinsOn Grate Assembly Locating Pins Indicated by Arrows Right Front LogLeft Front Log 5. Place left top log onto rear log and middle log locating pins as shown in Figure 15. 6. Place the center top log onto the rear log locating pin and middle log locating pin as shown in Figure 16. Left Top Log Locating Pins Center Top Log Locating Pins Figure 15 - Install Left Top Log Figure 16 - Install Top Center Log 11Note: Diagrams aND illustratioNs are Not to scale. 7. Place the right top log onto rear log locating pin and the right front log locating pin as shown in Figure 17. Right Top Log Locating Pins 8. Placelefttoptwig(24"and30"modelsonly)ontocorresponding notch on rear log as shown in Figure 18A. the front of the left top twig should be up against and behind the left top log. Left Top Twig Front Ember Bed Figure 17 - Install Right Top Log Figure 18A - Install Left Top Twig Left Top Log 9. Place the front ember bed log as shown in Figures 18A and 18B. Figure 18B - Completed Installation 18" Gas Log Set 24" Gas Log Set 30" Gas Log Set 12 Note: Diagrams aND illustratioNs are Not to scale. Top Burner Air Shutter Adjustment Procedure 1. if you have blue flame or the top burner is not carrying over and burning on all ports, the air shutter may need to be adjusted to 1/8" gap for both Natural and Propane gas. 2. check to see if the air shutter is set to 1/8" opening (see Figure 22). the air shutter is located on the rear left side of the appliance. 3. if the air shutter opening is more than 1/8" please loosen the air shutter screw and close completely which will set it to the 1/8" opening. Note: in some instances, propane appliances may need to be adjusted from the standard factory setting. Do Not open the air shutter greater than 1/4". Periodically check the positioning of all logs. Flame Appearance REFER TO THE OPERATING INSTRUCTIONS LOCATED AT THE BACK OF THIS MANUAL BEFORE LIGHTING THE APPLIANCE TO OBSERVE THE FLAMES. Flames from the pilot burner should be visually checked as soon as the appliance is installed. in addition a periodic visual check of the flames should be made. the pilot flame should always be present when the appliance is in operation (Figure 19). WARNING Failure to position the parts in accordance with Figure 21 or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. WARNING No adjustments are to be made to the ODS pilot system. Tampering with this system can be extremely hazardous. an incorrect pilot flame pattern is shown in Figure 20. this pilot flame will cause the thermocouple to cool. When the thermocouple cools, the log set will shut off. if pilot flame pattern is incorrect, or if log set shuts off, contact your service technician. Propane Pilot ShownPropane Pilot ShownBurner And Flame Characteristics the shadowdance™ gas log set features a new concept in integrated burner and log design. the flames from the burner travel horizontally through the log set and emerge at the knot holes. the flames are slightly blue off the burner and as they progress through the log set, they change to a light yellow color. Yellow decorative flames are visible as the flames exit the log set. When the log set is first lit, the flame may be entirely blue. light yellow flame will form at the top of the logs after several minutes of operation. the base of the log set and the underside of the top log glows a brilliant red. For an example of the log set, see Figure 21. Figure 19 - Correct Pilot Flame Figure 20 - Incorrect Pilot Flame Figure 21 - Proper Burner Flame Appearance in normal operation, at full rate, after 15 minutes the following flame appearance should be observed: Figure 22 - Top Burner Air Shutter Gap - 1/8" for NG & LP Using a 1/4" wrench loosen setscrew and adjust air shutter to 1/8" gap OPERATION AND CARE OF YOUR APPLIANCE 1. Appliance operation may be controlled through the ON/OFF unit rocker switch, located in the bottom front of the appliance or through an optional remote control. 2. When lit for the first time...

Baixe o seu

Para fazer o download, introduza 2 dígitos :