Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING-Changes or Modifications not expressly approved by the Manufacturer could void the user’s authority to operate the equipment. Wiring Information - Ground shield at one end only. - All terminal block wiring must be rated for 250V. - Power input wiring must be protected by a 15A double pole circuit breaker . - Terminal is for use only with equipment which has no live parts which are accessible . - Terminal is for use with equipment which maintains basic insulation from hazardous voltage under normal and single fault conditions . - Connection used at the remote end of external circuit . Recommended Wiring For AC Sensor — Power 3 Wire unshielded 22 AWG , 300 V Current Output 1 Pair shielded 24 AWG , 300 V Communication 1 Pair shielded 24 AWG , 300 V For DC Sensor— Power & Current output 3 Wire shielded 24 AWG , 300 V Status LED Terminal Block + 8 12– 30 VDC -- 7 6 DC Power Input Note - TB #7 is Connected to TB #4 RS232/485 L1 8 4-20 mA AC IN SHIELD 3 STATUS A/TX 2 B/RX 1 — 4 + 5 L2/N 7 6 SWITCH - F1/8 A 250V CALIBRATION FUSE Control Panel Fastening Screw ! Calibration Pushbutton NOTE — Use only 1/2” NPT Conduit Calibration — 4 -20 or 20 - 4 mA Output FULL — Calibrate 20 mA or 4mA (Set Near Target) 1. Calibration mode LED color is Green. (for Radar Low Dielectric Materials has to be off) 2. Push button and hold until LED turns Yellow (20 mA) or push button and hold until LED turns Red (4 mA) 3. Release button, observe LED flashes to acknowledge the calibration. EMPTY— Calibrate 4 mA or 20 mA (Set Far Target) 1. Calibration mode LED color is Green (for Radar Low Dielectric Materials has to be off) 2. Push button and hold until LED turns Red (4 mA) or push button and hold until LED turns Yellow (20 mA) 3. Release button, observe LED flashes to acknowledge the calibration. For Radar to turn the Low Dielectric Materials operation mode ON and OFF (this mode is recommended for materials with dielectric constant lower than 4.) 1) To turn the Low Dielectric Materials ON. Push button and hold until LED goes OFF after the sequence of Yellow , Red and turns Off. The Low Dielectric Material operation is On when the LED’S Green light blinks constantly. 2) To turn the Low Dielectric Materials OFF. Push button and hold until LED goes OFF after the sequence of Yellow , Red and Turns OFF. The Low Dielectric Material operation is OFF when LED is continuously Green. Operation - An ultrasonic/electromagnetic pulse is transmitted from the sensor . The pulse travels to the surface being monitored and is reflected off this surface back to the sensor . The time of flight is divided by 2 and converted to an output signal directly proportional to the material level . A C C U R A C Y R E S O L U T I O N Per Chart CALIBRATION PUSHBUTTON / Led Indicator For 4 - 20 mA (750 ohm Max.) output Deadzone +/—0.25% EMPTY 4 or 20mA 20 or 4 mA FULL Level Material S P A N LED RedYellow 12 30 Vdc 115 / 230 Vac 60 / 50 Hz . 1/2” NPT Conduit Hole 1”, 1 1/2”, 2” , 3”NPT Ultrasonic Sensor Radar Rod Antenna OPTIONAL Programmable Calibration & Diagnostics, Data Logging, RS232 or RS485 Com. Temperature Compensation for the speed of sound . Process Temperature Radar ;190° F/90°C — 40° F/°C Ultrasonic ; 140° F/60 °C — 40° F/° C Typical Installation 1) DIRECT MOUNTING ULTRASONIC SENSOR -SIMPLY THREAD SENSOR DIRECTLY INTO METAL OR PLASTIC NOZZLE. 2) RADAR UNIT MUST BE INSTALLED INTO METAL FITTING WITH THE ANTENNA POINTING DOWNWARD. Instruction Manual For LVU and LVRD Series Ultrasonic and Radar Sensors Inter-Connection Diagram Top View of Sensor (Access Cover Removed) FCC INFORMATION TO RADAR USERS NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING-Changes or Modifications not expressly approved by the Manufacturer could void the user’s authority to operate the equipment. Wiring Information - Ground shield at one end only. - All terminal block wiring must be rated for 250V. - Power input wiring must be protected by a 15A double pole circuit breaker . - Terminal is for us...
Este manual também é adequado para os modelos :Outras ferramentas - LVRD500 (2.78 mb)