Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Use a heat resistant material to protect the work surface. Glue sticks are not intended for ingestion and should not come in contact with food, etc. If swallowed, seek medical attention. Keep out of the reach of children. Before cleaning, adjustment or changing the attachments. Unplug the appliance and allow the attachment to cool. Never attempt to force cool the appliance after use by immersing any part of it in water or any other liquid. Allow the appliance to air cool only. 3 Keep the appliance away from all flammable material. Be aware that this product may ignite material. Where this is a concern, test a piece of scrap material. Never leave the appliance plugged in and unattended. After use, unplug the appliance, allow the attachment to cool and store in a safe place out of the reach of children. Fumes resulting from heating materials for craft activities may be hazardous. Always work in a well ventilated area. Seek advice on the materials being used. Never attempt to insert any material other than recommended glue sticks, sealer, or caulk sticks in the glue gun. For example: Do not attempt to melt crayons or candles. DO NOT use hot melt glue to take the place of structural fasteners. The glue sticks used with this glue gun will begin to soften at about 60°C. Don't use the glue on objects or materials that are subjected to heat. Avoid accidental glue discharge. Forcing glue sticks into an unheated appliance may damage the appliance or cause hot glue to be unexpectedly expelled from nozzle when the operating temperature is achieved. Glue may discharge from a heated appliance without pressure applied to the trigger (1). Return the appliance to the stand and use a heat resistant material to protect the work surface. This appliance is not a toy. Keep out of the reach of children. Safety symbols marked on appliance Hot surface do not touch. Appliance only to be used with the stand supplied. Electrical safety This appliance is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. This appliance is not intended for use by young or infirm persons without supervision. Children must be supervised to ensure they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Features 1. Trigger 2. Handle 3. Stand 4. Wire stand 5. Ready for use indicator Assembly Warning! Before cleaning, adjustment or changing the attachments. Unplug the appliance and allow the attachment to cool. Power connection (fig. A & B) The appliance can be used either in cordless or corded mode. In cordless mode the power supply is taken from the stand (3) to heat the element. This is suitable for small tasks where a small amount of glue is required. The heating element will start to cool as soon as the appliance is removed from the stand (3). When the ready for use indicator (5) changes to grey, or when the glue is no longer flowing freely, return the appliance to the stand (3). In corded mode the connector (6) can be removed from the stand (3) and inserted directly into the appliance. This is suitable for heavy duty tasks. Changing from cordless to corded operating mode (fig.C & D) X Remove the plug from the socket. X Push down on the two tabs in front of the connector (6) as shown. X Rotate the connector (6) toward the inside of the stand (3) and lift the receptacle and cord out of the holder. X Rotate the wire stand (4) forward (fig. D). X Insert the connector (6) into the handle (2) of the appliance (cord facing the back of the unit). Changing from corded to cordless operating mode X Remove the plug from the power supply socket. X Remove the connector (6) from the handle (2) of the appliance. X With the cable facing the rear of the stand (3) and the connections upwards insert the front of the connector (6) into the stand (3) location. X Push the rear of the connector (6) down to lock it in position. Fitting and removal of a glue tip attachment (fig. E) There are three different attachments: X Standard (7) X Extended angle (8) X Wide (9) X A wrench is included to change the attachment; it is stored in the stand (3). 4 X Use the wrench to rotate the glue tip attachment anti clockwise. Removing and changing attachments X Install the attachment and rotate it clockwise to tighten. Fitting a glue stick Replacement glue sticks are available from your Black & Decker dealer (cat. no. X72020-QZ) X Insert a stick of hot melt glue into the inlet tube located at the rear of the appliance. X Gently squeeze the trigger (1) to locate the glue stick firmly in position. Place the appliance into the stand (3) (Fig, A). X On first use, the glue stick may be completely inserted into the appliance. A second glue stick may be required. Warning! Do not attempt to remove an unused portion of a glue stick from the appliance. Use Warning! Be aware that this product ...
Este manual também é adequado para os modelos :Outras ferramentas - 496011-00 (545.12 kb)