Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 125 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury. Save These Instructions Do Not Discard Operating Instructions Lubrication This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty. 1. Disconnect the air supply from the tool to add lubricant. 2. Turn the tool so the air inlet is facing up. Place 4-5 drops of 30 W non-detergent oil into air inlet. Do not use detergent oils, oil additives, or air- tool oils. Air tool oils contain solvents which will damage the tool's internal components. 3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust. Recommended Hookup The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 50 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch or greater air hoses for 50 foot run or longer. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 50 psi and 125 psi. OIL O CO2 125 psi 150 psi or greater 50 psi Min. 125 psi Max. Minimum Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug Quick Coupler Operating Instructions PN001000 Operating Instructions (Continued) DRIvING A FASTENER 1. Connect the air supply to the tool. 2. Load fastener into nail gun. 3. Hold tool with nose pointed toward work surface. 4. Align fastener and tool in the location where fastener is to be driven. 5. Push gently against nail head to drive fastener. 6. Continue to apply pressure until fastener is driven completely or until reaching desired penetration. User -Maintenance Instructions TECHNICAL SERvICE Please call our Tool Hotline at 1-800543- 6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual. FASTENER AND REPLACEMENT PARTS Use only genuine Campbell Hausfeld 18 gauge fasteners (or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number. TOOL REPAIR Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. ASSEMbLY PROCEDURE FOR SEALS When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing. STORAGE The tool should be stored in a cool dry place. Troubleshooting Chart Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Symptom PossibleCause(s)*Corrective Action Air leaking between housing and cap 1. Loose screws in housing 1. Tighten screws 2. Damage to cap gasket 2. Replace cap gasket Air leaking through cap exhaust or nose 1. Air escaping from tool 1. Slap the cap side of the tool into the palm area of your hand with enough force to reset the internal piston 2. Damaged O-rings 2. Replace O-rings Nailer not setting fastener completely 1. Nail guide loose 1. Tighten nose guide 2. Inadequate air flow to nailer 2. Check hose, fitting, or compressor Nailer operates slowly or has loss of power 1. Nai...
Este manual também é adequado para os modelos :Outras ferramentas - IN730800AV (5.21 mb)