Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Do not lubricate them. Cleaning Bags Always empty the collection bags on a regular basis. Emptying the collection bags allows the machine to operate at a much higher level of efficiency. Always wear the appropriate respirator or dust mask and safety glasses when emptying the collection bags. Small dust particles can escape the bags during emptying, causing them to become airborne and easily inhaled. This microscopic airborne dust is extremely unhealthy to breathe and can cause serious health problems. While this dust collector excels at collecting the majority of wood dust produced by your machines, it is not an air filter; therefore, we strongly recommend the supplemental aid of a shop air filter such as the Grizzly G0572 or G9956. Air filters are designed to collect the smaller dust particles that dust collector bags cannot trap. -36- Model G0548Z-G1029Z2P (Mfg. 9/11+) Replacing Bags Cleaning Canister Filter Replacement plastic lower collection bags are available through Grizzly as Model T20543. Replacement top dust bags are available for the Model G1028Z2/G1029Z2/Z2P as Model G5556. To replace the collection bag: 1. DISCONNECT MACHINE FROM POWER! 2. Make sure you are wearing safety glasses and a respirator. 3. Release the belt clamp securing the collection bag, then unhook the bag from the collector. 4. Securely close the top of the bag and safely dispose of it according to local and federal standards. 5. Install a new collection bag. To clean the canister filter on the Model G0548Z/ ZP, move the canister cleaning handle back-and-forth to free the trapped dust particles from the filter pleats (see Figure 69). The particles will fall into the collection bag. The replacement canister for the G0548Z/ZP is the Model H5783, which can also be installed on the G1028Z2/G1029Z2/Z2P, if you would ever like to upgrade. Figure 69. Canister cleaning handle directions. NOTICE The use of compressed air or liquids to clean the canister filter will damage the filtration pleats of the filter. Use ONLY the cleaning handle or, if necessary, a soft brush to clean the inside of the canister filter. Model G0548Z-G1029Z2P (Mfg. 9/11+) -37- SECTION 8: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling. To reduce the risk of serious personal injury or damage to the machine, any repairs not covered in this manual should only be performed by or with the assistance of qualified service personnel. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start or a breaker trips. 1. Switch disabling key removed. 2. Power supply switched OFF or is at fault. 3. Wall fuse/circuit breaker is blown/tripped. 4. Wiring is open/has high resistance. 5. Motor ON/OFF switch is at fault. 6. Motor is at fault. 1. Install switch disabling key. 2. Ensure power supply is switched ON, ensure power supply has the correct voltage. 3. Ensure circuit size is suitable for this machine; replace weak breaker. 4. Check for broken wires or disconnected/ corroded connections, and repair/replace as necessary. 5. Replace faulty ON/OFF switch. 6. Test/repair/replace. Machine has vibration or noisy operation. 1. Motor, motor mount, or other mounting component is loose or broken. 2. Machine is incorrectly "mounted" or sits unevenly on its casters. 3. Motor fan is rubbing on fan cover. 4. Impeller is loose or damaged and unbalanced. 5. Motor bearings are at fault. 1. Retighten. Use thread locking fluid if necessary. Replace stripped fasteners or damaged components if necessary. 2. Tighten/replace anchor studs in floor if mounted; chock machine casters if mobile. 3. Replace dented fan cover; replace loose/ damaged fan. 4. Disconnect dust collector from power, and inspect the impeller for dents, bends, loose fins. Replace the motor and impeller as a set if the motor shaft and the impeller hub are damaged. 5. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -38- Model G0548Z-G1029Z2P (Mfg. 9/11+) Dust Collector Operation 1 VV |] Symptom Possible Cause Possible Solution Dust collector does not adequately collect dust or chips; poor performance. 1. Dust collection bags are full. 2. Canister is dirty. 3. Restriction in duct line. 4. Dust collector is too far away, or there are too many sharp bends in the ducting. 5. Lumber is wet and dust not flowing through ducting smoothly. 6. Leaks in ducting or too many open ports. 7. Not enough open branch lines, causing a velocity drop in the main line. 8. Ducting or machine dust ports are incorrectly sized. 9. The machine dust collection design is inadequate. 10. The dust collector is too small for the dust collection system, or ducting layout design inad...
Este manual também é adequado para os modelos :Outras ferramentas - G0548Z (3.26 mb)
Outras ferramentas - G1028Z2 (3.26 mb)