Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Remove the breather plug from breather tube. See figure 7. Pour approximately 3 gallons of Dexron transmission fluid ONLY into breather tube. 8 INLET HOSE STRAINER TUBE ASSEMBLY FIGURE 16 STRAINER TUBE ASSEMBLY If the ram does not move back and forth smoothly, the strainer tube assembly may be clogged. To clean, follow instructions for changing the reservoir oil, step number 1 through 3. Clean the strainer tube assembly and reassemble using a hydraulic pipe sealant .on the threads. nOSE CLAMPS Check the hose clamps on the bottom of the pump for proper tightness before each use. Hose clamps on the return hose should be checked once a season. STROKE RETURN STOP PLUNGER If the engagement handle does not return to neutral (from reverse) before the pressure relief bypass opens, loosen the hex lock nut, and back out the hex bolt one or two turns. See figure 17. NOTE When the pressure relief valve opens, a loud high pitched sound is heard and engine labors. Tighten hex lock nut and operate log splitter. Repeat if necessary. INSTALLATION OF TIRE TO RIM 1. Lubricate tire beads and rim flanges. HEX LOCKNUT STROKE RETURN STOP PLUNGER FIGURE 17 HEX BOLT 2. Do not exceed 30 P.S.I. when seating beads. 3. Adjust to recommended pressure after beads are sealed. OFF-SEASON STORAGE In event engine is to be stored for any length of time (30 days or more), prepare as follows: 1. Drain gasoline by tipping or by siphon hose, then run engine until remainder is used and tank and carburetor and empty. A CAUTION 2. 4. Drain into container outdoors away from fire or flame. Drain carburetor by running engine until it stops from lack of fuel. Protect the inside of engine for storage by removing spark plug and pouring one ounce of SAE 30 oil through spark plug hole into cylinder. Crank engine, without starting, several times to spread oil over cylinder walls. Never store outside without a waterproof cover. RAM OPERATION the ram does not move smoothly, run the ram its .all stroke several times to clear out air in the system. Be sure the breather valve is open. If this does not correct the problem, see Strainer Tube Assembly paragraph. 9 Models 642 and 645 This instruction manual covers various models, and ail specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 10 Models 642 and 645 PARTS LIST FOR LOG SPLITTER MODELS 642 and 645 c .vO. Part No. Color Code DESCRIPTION New Part Ref. No. Part No. Color Code DESCRIPTION New Part 1 717-0407 Control Valve 32 712-0123 Hex Nut 5/16-24 Thd.* 2 727-0231 Return Stroke High Pressure 33 710-0409 Hex Bolt 5/16-24 x 1.75" Hose Lg.* 3 727-0211 Forward Stroke High Pressure 34 750-0501 Filler Tube Hose 35 750-0442 Spacer .75" I.D. x 1.12" 4 737-0161 Breather Valve O.D. x 1.56" Lg. 5 737-0173 Female Adapter 3/4-14 x 36 734-1016 Wheel Ass'y. Comp. 4.80/ 1/4-18 N.P.T.F. 4.00 x 8 6 737-0153 Return Elbow 734-1017 Wheel Rim Ass'y. 7 726-0173 Hose Clamp 3/4" I.D. (Service Only) 8 727-0210 Return Hose 3/4" I.D. x 734-0872 Tire Only 4.80/4.00 x 8 2.62" Lg. (Service Only) 9 737-0172 Nipple 1/2-14 N.P.T.F. x 37 741-0107 Tapered Roller Bearing 1.5" Lg. 7 (Service Only) 10 710-0117 Hex Bolt 5/16-24 x 1.00" 38 714-0121 Cotter Pin 5/32" Dia. x 1.00 II Lg. (Grade 5) Lg.* 11 738-0406 Return Stroke Stop Plunger 39 734-0873 Hub Cap (Service Only) 12 750-0428 Engagement Handle 40 712-0299 Hex Castle Nut 3/4-16 Thd. 13 08118 Grip 41 712-0123 Hex Nut 5/16-24 Thd. 14 747-0355 Cylinder Support Rod 42 736-0119 L-Wash. 5/16" I.D.* (for 3-1/2" Dia.) (642) 43 714-0128 Sq. Key 1/4" x 1/4" x 1.00" 747-0354 Cylinder Support Rod Lg. (for 4" Dia.) (645) 44 736-0119 L-Wash. 5/16" I.D.* 5 737-0152 High Pressure 90° Elbow 45 710-0157 Hex Bolt 5/16-24 x.75" 3/8 N.P.T. x 9/16-18 Lg.* 16 Cylinder Ass'y. (See Page 12 46 727-0228 Suction Hose (642) for Breakdown) 727-0229 Suction Hose (645) 17 736-0169 L.-Wash. 3/8" I.D.* 47 Sq. Key (comes with Ref. 18 712-0798 Hex Nut 3/8-16 Thd.* No. 48) 19 15234 Strainer Tube Ass'y. 48 717-0460 Pump with Sq. Key 1/8" x 20 15235 Complete Oil Tank & Beam 1/8" x 1.00" Lg. (642) 21 710-0624 Hex Bolt 5/16-24 x 1.50" 717-0461 Pump with Sq. Key 1/8" x Lg- 1/8" x 1.00" Lg. (645) 22 712-0123 Hex Nut 5/16-24 Thd.* 49 712-0123 Hex Nut 5/16-24 Thd.* 23 736-0159 FI.-Wash. .34 I.D. x .88" O.D. 50 736-0119 L-Wash. 5/16" I.D.* 24 732-0252 Compression Spring .64 O.D. 51 717-0462 Flexible Coupling x .81 Lg. 52 710-0117 Hex Bolt 5/16-24 x 1.00" Lg.* 25 736-0160 FI.-Wash. .53" I.D. x .94" O.D. 53 13295 Coupling Support Brkt. Ass'y. 26 738-0234 Shld. Bolt .500" Dia. x .295 54 710-0216 Hex Bolt 3/8-16 x.75" Lg.* 27 711-0198 Pivot Bushing 55 736-0105 Belleville Wash. 3/8" ...
Este manual também é adequado para os modelos :Outras ferramentas - 242-642A (1.9 mb)
Outras ferramentas - 242-645A (1.9 mb)