Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. 15. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 16. Do Not exceed maximum tire pressure found on side wall of tire. 1 2 3 4 5 1 65238 HITCH ASSY 1 2 65240 HANDLE ASSY 2 3 65237 LOG SPLITTER 1 # PART # DESCRIPTION QTY 4 65239 AXLE ASSY 1 5 46503 WHEEL 2 CARTON CONTENTS PARTS PACKAGE PARTS PACKAGE 67812917 1516 # PART # DESCRIPTION QTY 6 49659 BOLT, HEX M10 x 252 7 49664 BOLT, HEX M8 x 254 8 49667 NUT, NYLOCK M84 9 R19171616 WASHER, FLAT 1/2 2 # PART # DESCRIPTION QTY 12 47810M NUT, NYLOCK M102 15 43343 COTTER, HAIRPIN1 16 23353 PIN, HITCH1 17 43010 COTTER, PIN 2 4 Figure 1 ASSEMBLY INSTRUCTIONS Figure 2 1 3 6 12 4 7 8 17 5 9 4 5 Tools Needed: (2) 17mm Open End Wrench (1) 14mm Open End Wrench (1) 13mm Open End Wrench (1) Pliers 1. Verify that all parts and all fasteners (Shown full size) on page 4 are included in the carton and parts bag. Refer to page 4 to identify fasteners used in the following instructions. 2. With the Log Splitter(3) standing on end, attach the Hitch Assy(1) using two M10 x 25 Hex Bolts(6), and secure with two M10 Hex Nuts(12). Be sure that all bolts are tight. (Figure 1) 3. Attach Axle Assy(4) to the Log Splitter(3) using four M8 x 25 Hex Bolts(7), and secure with four M8 Hex Nuts(8). Be sure that all bolts are tight. (Figure 1) 4. Slide the Wheel(5) on to the Axle Assy(4) with the long hub facing inwards. Slide a 1/2 Flat Washer(9) onto the outside of the axle. Secure with Cotter Pin(17), bend the ends with a pair of pliers. (Repeat for other wheel) (Figure 2) 5. This Log Splitter will attach and tow behind any standard lawn and garden tractor. Use the supplied Hitch Pin, and Haircotter Pin to attach to tractor. In addition there is a hitch located on the rear of the unit, which allows you to tow a cart behind the Log Splitter. 6. As shown during assembly this unit will stand on its end for easy storage. 6 Figure 3 HANDLE RELEASE SCREW Gather the logs you wish to split. Make sure the maximum length of each log does not exceed 18". If the log does exceed that measurement, you must cut the log to fit the maximum length of the tool. Make sure the Piston Rod is fully retracted into the cylinder. If necessary, turn the RELEASE SCREW counterclockwise to release the hydraulic pressure. Tighten the RELEASE SCREW. Place the log between the Wedge and Piston Assembly. Rest the log in the metal bracket Cradle. Wear eye proctection (goggles) when operating the Hydraulic Log Splitter After every use, wipe down the Hydraulic Log Splitter to remove any tree sap or dirt left behind. This will extend the life of the tool. Bleeding The Log Splitter 1. Operate the log splitter to extend the Piston Rod to its maximum length. 2. Remove the Oil Filling Plug. 3. Turn the Release Screw counterclockwise as fast as possible, the Piston Rod will retract and push air from the cylinder out of the Oil Filling Plug. 4. Replace the Oil Filling Plug. Repeat steps 1-4 as necessary. Maximum Log Length: Ram Stroke: Cradle Dimensions: Base Dimensions: 18" 8-1/16" 3-3/4" x 4" x 4" 42-1/8"L x 8-1/16"W x 37"H It is recommended you operate the Log Splitter in the following manner. Stand behind the log splitter and grip one Handle in each hand and pump the Handles in a back-and-forth motion with one Handle fully forward and one fully rearward as shown in figure 3. Repeat Step "5" to advance the Piston Rod forward. This will push the log against the Wedge and Split it. When you have split the log, remove the split pieces. Turn the RELEASE SCREW counterclockwise to draw the piston rod back into the cylinder. Tighten the RELEASE SCREW when the piston rod has retracted fully. When you are done, it is recommended you store your Hydraulic Log Splitter with the RELEASE SCREW opened to relieve any hydraulic pressure during non-use. OPERATION MAINTENANCE SPECIFICATIONS TROUBLE SHOOTING 1. 2. 3. 4. 5. If hydraulic cylinder does not move forward when pumping handles. A. Check to see if Release Screw is tightened in the closed position. B. Check to see if you need to add hydraulic oil. 1. 6. 7. 8. 9. Adding Oil If you should need to add hydraulic oil to the Log Splitter, turn the release screw counterclockwise to retract the piston rod, remove the Oil Filling Plu...