Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
A B B DE 1, Turn base (A) right side up, Align the mounting hobs at the base of blower and motor assembly (B) with six pre-drilled hobs (C) in base and fasten with six 5/16=18 x 5/8" hex head screws (D) and 5/16" lock washer (E), See figure 8, Fig. 9 G 2, 3, 11 Assemble drum support (F) to the two threaded hobs in the corner of base with two 5/16=18 x 5/8" hex head screws and 5/16" lock washer (G), NOTE: Do not completely tighten hardware at this time, See figure 9, Assemble the remaining drum supports to the base in the same manner, NOTE: Do not completely tighten hardware at this time, 5, Align the hobs in the drum support with the hobs in the drum (M), Place a 5/16" lock washer on a 5/1618 x 5/8" hex head screw, then 5/16" fiat washer onto the hex head screw, insert the hex head screw thru the hob in drum support and drum, Thread a 5/16" hex nut onto the hex head screw and tighten securely, See figure 11, Fasten the remaining drum supports to the drum in the same manner, Fig. 12 T 4, Assemble U-Bracket (H) to Drum (J), Place a 5/16" lock washer then a 5/16" fiat washer onto a 5/1618 x 5/8" hex head screw (K) thru the hob in the U-Bracket and the hob in the drum, thread a 5/16" hex nut onto the hex head screw, Repeat this process for the remaining hob and securely tighten both screws, NOTE: U-Bracket should be mounted to the right side of opening (L) in the drum as shown, See figure 10, 8, Place one end of 6°inch diameter flexible hose (N) Fig. 11 over blower/motor outlet(R), Slide one 6°inch diameter hose clamp (S) down 6°inch flexible hose and tighten hose clamp to blower/motor outlet, See figure 12, ME 7, Place the other 6-inch hose clamp (T) over the 6-inch flexible hose, Attach the 6-inch flexible hose to the drum inlet (U) and tighten 6-inch hose clamp, See figure 12, 12 1, Fig. 13 Align the four hobs in intake port (A) with the // V 8, Attach the lower dust bag retaining clip (V) to the dust collector drum, Align both hobs (W) in the retaining clip with the two hobs in the drum, insert a 1/4-20 x 5/8" hex head screw through each hob in the retaining clip and drum, Place a 1/4" fiat washer and 1/4-20 hex nut onto screw inside of the drum, Repeat this process for the other three retaining clips and tighten all hardware, See figure 13, iNTAKE PORT TO BLOWER MOTOR ASSEMBLY MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE. Fig. 14 B A mounting hobs in flange (B) of blower and motor assembly and fasten with four M4,2 sheet metal screws (C), See figure 14, Fig. 15 0 0 E D 2, Attach one intake port cap (D) to the intake port (E), The intake port caps must be placed into the intake ports when the intakes are not in use, See figure 15, IMPORTANT: When connecting an intake hose to one or both intake ports, DO NOT REMOVE THE INTAKE PORT CAP COLLARS (F} FROM THE INTAKE PORTS, Slide the collar further back when attaching a hose, See figure 15, NLTER AND COLLECTION BAG TO DRUM ASSEMBLY MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE. 1, Hook the loop (A) on the top filter bag onto hook (B) of the upper support rod, See figure 17, 13 Fig. 16 \ D 2, Slide the lower support rod (C) onto the end of the upper support rod (B), Raise the assembled support rod with filter bag attached and place the end of the lower support rod into the hobs of the U=bracket (D), The flared end of lower support rod will prevent the rod from sliding through the U=bracket, See figure 16, G FE 3, insert locking band (E) through all the loops of filter bag (F), Position the open end of the filter bag over the top lip of the drum, Make certain the locking band is positioned in the upper recessed channel of the drum and fasten clamp (G) securely to drum, See figure 17, 4, Place the second locking band through all the loops of the collection bag, similar to the filter bag, 5, Place the collection bag over the lower lip of the drum, Pull up on the retaining clips and insert cop lection bag underneath each retaining clip, Make certain the locking band is positioned in the lower recessed channel of the drum and fasten clamp securely to drum, FLEXIBLE HOSE TO iNTAKE PORT ASSEMBLY MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE. IMPORTANT: When connecting an intake hose to one or both intake ports, DO NOT REMOVE THE INTAKE PORT CAPS FROM THE INTAKE PORTS, Slide the collar further back the intake port when attaching a hose, 1, To attach the 4-inch flexible hose to one of the intake ports, pull the intake port cap from the intake port, Slide the collar of the intake port cap further back the intake port and let the cap hang from the intake port, 2, Place 4=inch hose clamp over 4=inch flexible hose, Slide hose over one intake port opened Step 1 above and tighten hose clamp, 3, if you wish to use the second intake port, you should purchase a second 4=inch flexible hose and 4=inch hose clamp and repeat Steps 1 and 2 above, See your nearest Sears Hardware Department or Sears Power and Hand Tool Cat...