Assessments - , GPA: ( )

Instruções de Operação Philips, Modelo HF3465/01

Fabricante : Philips
Arquivo Tamanho: 980.81 kb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

Note: It takes approx. 1 second for the lamp to go on.This is normal, the lamp needs to heat up. Note:The light intensity you have selected is automatically set as the light intensity level for the alarm as well. Tip:When you use the appliance for the first time, set the light intensity to 20.The moment you wake up, check which light intensity level the appliance has reached by briefly pressing the light intensity + or - button.When you do this, the current alarm light intensity level appears on the display. Set the alarm light intensity to this level for the next day. 3 To switch off the lamp, press the lamp on/off button again. setting the alarm When you set the alarm, you choose an alarm time and (only in case of HF3470) the type of sound you want to wake up to. The alarm is set when the alarm symbol is visible on the display. The light intensity slowly increases to the selected level during the last 30 minutes before the set alarm time. The sound slowly increases in 90 seconds to the selected level after the set alarm time. Note:You can set the light intensity by pressing the light on/off button and then pressing the light intensity + or - button and you can set the alarm volume by pressing the volume increase or decrease button. If you do not want to wake up to the lamp or to a sound, select a light intensity or volume level of 0. See sections ‘Using the lamp’ and ‘Radio/Volume’ in this chapter. 1 Push the control lever down to the middle position to switch on the alarm. (Fig. 13) The hour indication of the alarm time flashes (Fig. 14). , To adjust the time, follow steps 2 to 5. If the alarm time is correct, just wait a few seconds. ,2 Press the menu + or - buttons to select the hour (Fig. 9). Note:You can only do this when the hour indication flashes. If this is not the case, push the control lever up and down again to enter the alarm time mode.You can also set the alarm time in the menu. See section ‘Menu functions’ in this chapter. 3 ,4 5 Press the SELECT button to confirm (Fig. 10). The minute indication of the alarm time starts to flash (Fig. 15). Press the menu + and - buttons to select the minutes. (Fig. 9) Press the SELECT button to confirm or wait for a few seconds (Fig. 10). The appliance leaves the menu and the display shows the clock time. , The alarm time is now set. switching off the alarm To switch off the alarm function, push up the control lever to the top position. Note:The lamp stays on to light your room.You can switch off the lamp by pressing the light on/off button. Note:The alarm (sound and/or light) automatically switches off after 90 minutes. 10 EnglisH setting the alarm sound (HF3470 only) See section ‘Menu functions’ above. You can choose one of the following sounds: -Radio (Fig. 16) -Birds (Fig. 17) -Beep (Fig. 18) snoozing 1 , Push down the control lever to the bottom position when the alarm goes off. (Fig. 19) The lamp continues to be on at the selected intensity level, but the alarm sound stops. After 9 minutes, the wake-up sound is automatically played again. Note:The 9-minute snooze time is fixed.This time cannot be adjusted. Note: If you push down the control lever with too much force, it may jump back to off position. alarm demonstration If you want to get a quick demonstration (60 seconds) of the gradually increasing light level and sound level, activate the test function of the appliance. 1 Push the control lever down to the bottom position for a few seconds until TEST appears on the display (Fig. 20). 2 Push the control lever down again to stop the demonstration. Note:The appliance continues to run the alarm demonstration until you push down the control lever again.The test automatically stops after 9 hours. radio/volume (HF3470 only) 1 To switch on the radio, press the radio on/off button. (Fig. 21) 2 To select the desired radio frequency, press the menu + and - button. (Fig. 9) Tip:To scan radio frequencies automatically, press and hold the menu + or - button for approx. 2 seconds. Tip:To make sure you get a good radio signal, fully unwind the antenna and move it around until you have found a position at which reception is best. To switch off the radio, press the radio on/off button again. volume To set the volume, press the volume increase or decrease button. (Fig. 22) 3 1 HF3470:You can choose a volume level between 1 and 20. HF3465:You can choose a volume level between 1 and 10. Note:The volume level you have selected is automatically set as the volume level for the alarm as well. setting the display brightness 1 2 3 4 5 Press the MENU button to enter the menu (Fig. 8). Press the menu + or - button to select the display brightness menu (Fig. 9). Press the SELECT button to enter the display brightness menu (Fig. 10). Press the menu + and - button to change the display brightness (Fig. 9). Press SELECT to confirm (Fig. 10). EnglisH 11 cleaning and maintenance Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to cle...