Assessments - 2, GPA: 3 ( )

Fabricante : Pioneer Arquivo Tamanho: 3.17 mb Arquivo Nome : Língua de Ensino:

3-11) • Never drag the system along the floor when moving the units. • The lenticular sheet damages very easily as it is very thin. Therefore move it gently and do not apply excessive shock or vibration to it. • As the panels supporting the screen are very thin and deform easily, be careful that they do not hit or get hooked onto surrounding objects when moving them. 3. PRECAUTIONS FOR TRANSPORTATION Do not stack the units on their sides or backs when transporting them. Always place them upright. If they are stacked on their sides or backs, vibration and shock may cause damage or fire hazards. INSTALLATION AND ASSEMBLY 4. ASSEMBLING THE SYSTEM (1) Assembling the Projection Frame (RMF-V4011/V5011) Assemble the projection frame as follows. [1] Mount the stopper onto the base assembly and tighten the screws (M5 . 35). (2 . 2 points) [2] Mount the H-shape frame assemblies (R) and (L), and tighten the screws (M5 . 10). (4 . 4 points) [3] Mount the horizontal frame assemblies (two) and tighten the screws (M5 . 10). (4 . 4 points) * As for the positions for tightening the screws in steps 2 and 3, push the frame against the corner fixtures in the two directions indicated by the arrow. [4] Mount the shield onto the H-shape frame assembly (L) using the rivets, peel off the paper on the shield and paste a magic tape on the H-shape frame assembly (L). [5] Attach the fixtures (R) and (L) and tighten the screws (M5 . 10). (3 . 2 points) [6] Place the projection unit on the base assembly, and secure the fixtures (R) and (L) and projection unit to each other with the screws (M5 . 10). (2 . 2 points) [7] Secure the movable part of the base assembly with the two screws (M5 . 35). 3 Horizontal frame assembly H-shape frame assembly (L) 4. Rivet A-5 Holder (L) 2 H-shape frame A-7 assembly (R) B-6 Screw (M5 . 35) A-5 Holder (R) 5 Shield 2 H-shape frame assembly (L) Table 1 Screw (M5 . 35) 1 Stopper B-5 Guide fixture 1 Base assembly (Fig. 3-13) INSTALLATION AND ASSEMBLY (2) Assembling the System The basic procedure for assembling the system is as follows. 1 Assemble the projection stand (RM-V112/RMA-V5010). 2 Mount a one-link mount unit . (40-inch only) 3 Assemble the projection frame (RMF-V4011/V5011). 4 Mount the multi-projection unit (RM-V4000V/V5000V). 5 Mount the projection screen kit (RMS-V4011/V5011). 6 Mount the top board , side board , rear panel. The basic procedure for assembling the system for rental-use is as follows. 1 Assemble the projection stand (RM-V112). 2 Mount the 2-link/3-link mount unit (RMA-V2050/V2060). 3' Mount the multi-projection unit (RM-V4000V) to the projection cabinet (RMF-V4011R). 4' Mount the projection cabinet (RMF-V4011R). The above procedure is recommended. It is explained below. 1 Projection Install Tables (RM-V112/RMA-V5010) Place the installation tables (RM-V112) at the specified position and link them together with the bolts and nuts specified. First tighten the bolts and nuts temporarily, and after all have been linked, check their height differences and if they are horizontal before tightening the nuts and bolts firmly. Do not tighten the adjusters at the legs as their final positions have to be adjusted after assembling all units. To install at a height greater than the installation table when not using this table, make sure the strength is greater than required. 2 Mount Unit (RMA-V2050/V2060) Place the mount unit on the stand and join them using the specified bolts and nuts. As the horizontality, difference in level, etc. of the mount units form the basis of the whole system assembled, assemble them accurately. If gaps are formed between the mount unit and the stand due to the difference in height, use the floor leveler of the stand to adjust the height, or place spacers between the mount unit and stand (metal plates about 1 to 2 mm thick). When using several mount units, adjust their height, horizontality, etc. In the case of the system for rental-use, mount the conventional mount units (RMA-V2050/V2060) using the conventional method. For details, refer to the RM-V2000A technical manual. INSTALLATION AND ASSEMBLY 4 Multi Projection Unit (RM-V4000V/V5000V) The Multi-Projection Unit is designed to be mounted from the back of the cabinet normally. If sufficient space cannot be left at the back, it can be mounted from the front. Mount from front Mount from back (Fig.3-18) a When mounting from the back [1] Pull the table of the cabinet to the back. (Fig. 3-19) [2] Insert the (M5 . 35) into the holes (Fig. 3-20) on the table. (To prevent the table from moving when placing the projection unit.) [3] Place the multi-projection unit on the table and decide the position. The position should be so that the front of the multi-projection unit will touch the metal fixtures while the sides touch the guide fixtures (right side as viewed from the screen side). (Fig. 3-21) [4] Secure the multi-projection unit to the metal fixtures of the cabinet with the four (M5 . 50). (Fig. 3-22) [5] Remove the insert...

Baixe o seu

Para fazer o download, introduza 2 dígitos :