Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
Refer to page 12 for list of cables and adaptors. A. Signal connector: 15-pin mini D-sub (PC/AT compatible model) Connect the signal cable to the 15-pin mini D-sub connector on the LCD Projector unit. B. Signal connector: 15-pin D-sub (MAC) To convert a MAC 15-pin D-sub connector to a 15-pin mini D-sub connector, use a VGA-MAC adaptor (included) and connect it to the 15-pin mini D-sub connector on the LCD Projector unit. MAC 15 15 11 Pin No. Signal 1 Ground for red video signal 2 Red video signal 3 Composite sync 4 Ground 5 Green video signal 6 Ground for green video signal 7 Unused 8 Unused 9 Blue video signal 10 Unused 11 Ground 12 Vertical synchronizing signal 13 Ground for blue video signal 14 Ground 15 Horizontal synchronizing signal n Pin No. Signal 1 Red video signal ? Green video signal 3 Blue video signal 4 Unused 5 Unused (Through out) 6 Ground for red video signal 7 Ground for green video signal ft Ground for blue video signal 9 Unused 10 Ground 11 Unused 12 Unused 13 Horizontal synchronizing signal 14 Vertical synchronizing signal 15 Unused * For input adaptor only Note: • When using a Composite Sync Output type Macintosh, please use a Composite Sync type VGA MAC Adaptor (pin 3 and pin 13 are connected). 17 C. RS-232C Connector: 9-pin D-Sub Connect the RS-232C Cable to the 8-pin mini DIN connector on the LCD Projector unit. D. RS-232C Connector: 8-pin mini DIN To convert a 9-pin D-Sub connector to a 8-pin mini DIN connector, use a RS-232C 9-pin adaptor (included). Connect the 9-pin D-Sub adaptor and RS-232C cable. Then, connect it to the 8-pin mini DIN connector on the LCD Projector unit. 5 1 © J > • • • < • • • • 9 6 6 8 Pin No. Signal 1 Unused (Request to send) ? Unused (Clear to send) 3 Transmitted data 4 Ground 5 Received data 6 Unused 7 Unused 8 Unused Pin No. Signal 1 Unused 2 Received data 3 Transmitted data 4 Unused 5 Ground 6 Unused 7 Unused (Request to send) 8 Unused (Clear to send) 9 Unused E. RS-232C connector: 25-pin D-Sub To convert a 25-pin D-Sub connector to a 8-pin mini DIN connector, use a RS232C 25-pin adaptor (included). Connect the 25-pin D-Sub adaptor and RS-232C cable. And then connect it to the 8-pin mini DIN connector on the LCD Projector unit. 13 1 n¥ Ih I 25 14 1 5 °Vp 6 9 Pin No. Signal 1 Unused 2 Received data 3 Transmitted fdata 4 Unused 5 Ground 6 Unused 7 Unused (Request to send) 8 Unused (Clear to send) 9 Unused Pin No. Signal 1 Unused 2 Transmitted data 3 Received data 4 Unused (Request to send) 5 Unused (Clear to send) 6 Unused 7 Ground 8-25 Open А Basic LCD Projector Operation Before you begin, make sure... • All connections are made. (See pages 10 and 13 to 16.) • LCD Projector is positioned properly. (See page 9.) • LCD Projector is plugged in. • Remove lens cap. • You have read Important Safeguards. (See pages 2, 3.) 1 Press the Main Power Switch ON. The LAMP STATUS indicator lights red on the top panel. • The first time you turn on the power, or whenever the LAMP STATUS indicator is not lit, press the Main Power Switch (ON/OFF) to turn on the power. 2 Press LAMP ON/OFF Switch on the LCD Projector ON. When the LAMP ON/OFF Switch is turned on, the red LAMP STATUS indicator changes to green. When the LAMP ON/OFF Switch is turned off, the green LAMP STATUS indicator changes to flashing red while the LCD Projector cools down and then to solid red when fan stops. OFF MAIN ON Main Power Switch Located on rear of the LCD Projector. See page 7. ZOOM RING FOCUS RING When the power is on, the LAMP STATUS indicator indicates the operating condition of the lamp. Red: Main Power On (Lamp Off) Green: lamp is ready Flashing green: warming up Flashing red: Cooling Fan operating LAMP ON/ OFF Button LAMP STATUS \ Indicator ' See page 27, “Maintenance Indicators'’, for details. Open door cover and press INPUT or press INPUT on the remote control to select the desired input mode. Continue to press INPUT to set the desired input mode. Each press will change the display as shown below: (Inside the Door) L ® OOÜÖOQ LrtWTrtfC* fltVEFWfc VDEOiiOJ ИШИ INPUT Button VOLUME +/-Buttons OR • If unit is connected with both VIDEO and S-VIDEO cables, the S-VIDEO mode has priority. A Turn on your computer (RGB) or start video playback (Video or S-Video). • Adjust FOCUS and ZOOM RING if necessary. #TC Press VOLUME +/- on the remote or LCD Projector to adjust the volume level of the built-in speaker. The number of segments (0 - 63) increases or decreases as the volume is adjusted. 24 IIIIINII1M.............. л Press LAMP ON/OFF on the LCD Projector OFF. • Do not turn off the Main Power Switch until the LCD Projector cooling fan has stopped and LAMP STATUS indicator turns solid red. vamute CD AM LTTE -VQLUME CD CD- MOOE О NRL/T C3- CD CD CD LSTANDARO-J VOLUME +/-Keys INPUT Key Video Adjustment This LCD pr...