Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least 10cm (4”) of space], otherwise burns or damage could result. Projector NOTE: BDuring projection of an image, the cooling fan will operate, emitting a small noise as it operates. This noise may change depending on the ambient temperature. Turning the lamp on or off will cause this noise to increase a little. BBy using the “OPTION” menu to set “LAMP POWER” to “LOW”, the operating sound of the fan can be reduced. (Refer to page 47.) # ( $% ' & Connector panel #$%&(' )+*, #$%&(' )+*, # SERIAL connector (pages 20, 21, 22 and 64) This connector is used to connect a personal computer to the projector in order to control the projector externally. (RS-232C compatible) $ RGB1 IN connector (pages 20 and 21) This connector is used to input RGB signals and YPBPR signals. % RGB2 IN/1 OUT connector (pages 20, 21 and 46) This connector is used to input or output RGB signals and YPBPR signals. Adjust “RGB2 SELECT” in the “OPTION” menu to select whether you want input or output with this connector. & S-VIDEO IN connector (pages 22 and 42) This connector is used to input signals from S-VIDEO-compatible equipment such as a video deck. The connector is S1 signal compatible, and it automatically switches between 16:9 and 4:3 aspect ratios in accordance with the type of signal being input. ' AUDIO IN L-R connectors (for S-VIDEO/VIDEO) (page 22) Only one system is provided, so connect the appropriate connectors when using S-VIDEO or VIDEO. ( Menu operation (page 16) ) VIDEO IN connector (page 22) This connector is used to input video signals from video equipment such as a video deck. 14-ENGLISH * AUDIO OUT connector (pages 20, 21, and 22) This connector is used to output the audio signals which are input to the projector. If audio equipment is connected to this connector, no sound will be output from the built-in speakers. + RGB AUDIO 1IN/2IN connectors (pages 20 and 21) These connectors are used to input audio signals, and they correspond to the RGB1 IN/2 IN connectors respectively. , Power input socket (AC IN) (page 24) The accessory power cord is connected here. Do not use any power cord other than the accessory power cord. Preparation ENGLISH-15 Menu operation Remote control unit FREEZE SHUTTER INDEX WINDOW PROJECTOR STD AUTO SETUP INPUTPOWER MENU ENTER VIDEO RGB VOLUME D.ZOOM ' ( + - ./ 012, ) * Projector control panel #$% '( & ) * +, FREEZE SHUTTER INDEX WINDOW PROJECTOR STD AUTO SETUP INPUTPOWER MENU ENTER VIDEO RGB VOLUME D.ZOOM ' ( + - ./ 012, ) * Projector control panel #$% '( & ) * +, # RGB INPUT indicator This indicator illuminates when a signal is being input to the connector (RGB1 IN or RGB2 IN) selected using the input select buttons. $ LAMP indicator (page 53) This indicator illuminates when it is time to replace the lamp unit. It flashes if a circuit abnormality is detected. % TEMP indicator (page 52) This indicator illuminates if an abnormally high temperature is detected inside 16-ENGLISH the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. & Illumination sensor (page 39) This sensor detects the luminance when the “DAYLIGHTVIEW” function is operating. Do not cover the projector and do not place any object on the projector when using it. ' POWER button (pages 24, 26 and 27) This button is used to turn the power on and off. This button on the projector illuminates red when the projector is in standby mode, and it illuminates green when a picture starts to be projected. ( INPUT buttons (page 25) These buttons are used to switch the input signals from the connected equipment. ) AUTO SETUP button (pages 25 and 28) If this button is pressed while a picture is being projected, the projection settings will be adjusted automatically in accordance with the signal being input. In addition, the angle of tilt of the projector will be automatically detected and adjusted in order to correct any keystone distortion. * MENU button (pages 32 and 34) This button is used to display the “MAIN MENU”. When a menu screen is being displayed, this button can be used to return to a previous screen or to clear the screen. + Arrow (F FFG GGI II and H HH) buttons (page 34) These buttons are used to select and adjust items in the on-screen menus. , ENTER button (page 34) This button is used to accept and to activate items selected in the on-screen menus. -FREEZE button (page 29) This button is used to momentarily freeze projection so that a still picture is displayed. . SHUTTER button (page 29) This button is used to momentarily turn off the picture and sound. / VOLUME +/- buttons (page 30) These buttons are used to adjust the volume of the sound that is output from the projector’s built-in speakers and AUDIO OUT connector. Refer to page 33 for details on how to adjust the volume without us...
)
