Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Place the projector as far away from light sources as possible. BIf facing the remote control unit toward the screen to operate the projector, the operating range of the remote control unit will be limited by the amount of light reflection loss caused by the characteristics of the screen used. 24-ENGLISH Getting started ENGLISH-25 Turning on the power Make sure that all peripheral devices are connected properly before turning on the power. & $ ( $ ( ') & * & ' # AC IN socket Connector Connect the accessory power cord to the AC IN # socket. BInsert the connector into the AC IN socket so that the shape of the connector matches the shape of the socket. Then insert the power cord plug into the wall outlet. BThe POWER button on the projector will illuminate red. Press the POWER button. $ $ BThe POWER button on the projector will flash green. After a short period, it will illuminate green, and the startup logo will be displayed. If you would like the startup logo not to be displayed, set “STARTUP LOGO” to “OFF”. (Refer to page 49.) Turn on the power of all connected devices. % BStart the play function of a device such as a DVD player. NOTE: BA tinkling sound may be heard when the lamp unit is turned on, but this is not a sign of a malfunction. 26-ENGLISH ENGLISH-27 Basic operation Select the input signal by pressing the INPUT SELECT button or the DIRECT INPUT SELECT buttons. BA picture will be projected in accordance with the selected input signal. (page 30) BWhen “SIGNAL SEARCH” is set to “ON”, the projector detects which signals are being input, and uses these signals for projection. BIf no signal is detected, the guide screen for computer connection will be displayed (when “INPUT GUIDE” in the “OPTION” menu is set to “DETAILED”. Refer to page 69 for details). BPress the INPUT SELECT button to finish the input signal search. Follow the procedure below when you set the projector up first, and when you change the placement after original setup. Press the AUTO SETUP button (when RGB signals are being input). BSettings such as the position of the image will be corrected automatically. (page 31) Adjusting the size BTurn the zoom ring to adjust the size of the projected image. Adjusting the focus BTurn the focus ring to adjust the focus of the projected image. & ' ) * ( Adjusting the angle BPlace the projector so that it is vertical to the screen. BWhile pressing the adjuster buttons, adjust the forward/back angle of tilt of the projector. Adjust so that the projected image is placed at the center of the screen. Direct power on function If “DIRECT POWER ON” in the “OPTION” menu is set to “ON”, projection will start after the power cord is connected. Refer to page 51 for details. #.$ #.$ % 28-ENGLISH NOTE: BYou can also turn off the power by holding down the POWER button for at least 0.5 seconds. NOTE: BPress any button other than the POWER button to cancel the “POWER OFF” screen. BThe “POWER OFF” screen will disappear in 10 seconds. Turning off the power Press the POWER button. BThe “POWER OFF” confirmation screen will be displayed. Press the POWER button again. BThe lamp unit will switch off and the picture will stop being projected. (The POWER button on the projector will illuminate orange while the cooling fan is still operating.) # $ %Disconnect the power cord after the POWER button on the projector illuminates red. BDisconnect the power cord plug from the wall outlet first, and then disconnect the connector from the AC IN socket. AC IN socket Connector Direct power off function You can disconnect the power cord during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp. BWhen this function is used, it may take more time for the lamp to turn back on again compared to when the lamp cools down with the power cord connected. BDo not put the projector in a bag while the POWER button on the projector is illuminated. CAUTION If not using the projector for an extended period of time, disconnect the power cord plug from the wall outlet. BIf dust builds up on the power cord plug, the resulting humidity may damage the insulation, which could result in fire. BThis projector continues to draw approximately 4 W of power even when the power is turned off. POWER button on the projector POWER button status Projector status Red Illuminated The projector is in standby mode and image projection is possible by pressing the POWER button. Green Flashing The projector is preparing for projection after the power has been turned on while the POWER button on the projector is illuminated red. (After a short period, a picture will be projected.) Illuminated A picture is being projected. Orange Illuminated The lamp is cooling down after the power has been turned off or while direct power off function is operating. Flashing The projector is preparing for projection after the power has been turned on while the POWER button on the projector is illuminated or...