Assessments - 2, GPA: 5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Use the following table as a guide. Distance between the screen and the center of the lens Screen Unit: m (feet) Screen size (inches) 40 60 80 100 120 150 180 200 250 300 Minimum 1.2 1.8 2.4 3.0 3.6 4.5 5.4 6.0 7.5 9.0 Distance (3.9) (5.9) (7.9) (9.8) (11.8) (14.8) (17.7) (19.7) (24.6) (29.5) Maximum 1.4 2.0 2.7 3.4 4.1 5.2 6.2 6.9 8.7 10.4 Distance (4.6) (6.6) (8.9) (11.2) (13.5) (17.1) (20.3) (22.6) (28.5) (34.1) There may be a slight difference between the actual value and the design value shown in the table above. For details on installation, see “Installation Diagram” on page 50. Installing the Projector To connect a computer Connecting the Projector When you connect the projector, make sure to: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals. When pulling out a cable, be sure to pull it out by the plug, not the cable itself. Connecting a Computer This section describes how to connect the projector to a computer. For more information, refer to the computer’s instruction manual. Projecting the Picture AStereo audio connecting cable (not supplied) (Use a no-resistance cable.) BHD D-sub 15-pin cable (supplied) Right side to monitor output Computer to audio output Notes • The projector accepts VGA, SVGA, XGA, SXGA, and SXGA+ signals. However, we recommend that you set the output mode of your computer to XGA mode for the external monitor. • If you set your computer, such as a notebook computer, to output the signal to both your computer’s display and the external monitor, the picture of the external monitor may not appear properly. Set your computer to output the signal to only the external monitor. Connecting the Projector For details, refer to the operating B Video cable (not supplied) or S-Video cable (not supplied) instructions supplied with your computer. To connect to a video GBR/ Component output connector Note To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor. Connecting a VCR This section describes how to connect the projector to a VCR. For more information, refer to the instruction manuals of the equipment you are connecting. To connect to a video or S video output connector AStereo audio connecting cable (not supplied) (Use a no-resistance cable.) VCR to S video output Right side to audio output (R) to video output to audio output (L) AStereo audio connecting cable (not supplied) (Use a no-resistance cable.) BSignal Cable (not supplied) HD D-sub 15-pin (male) - 3 . phono jack Right side to audio output (R) VCR to video GBR/ component output to audio output (L) Notes • Set the aspect ratio using “Wide Mode” on the INPUT SETTING menu according to the input signal. • When you connect the projector to a video GBR output connector, select “Video GBR” or when you connect the projector to a component output connector, select “Component” with the “Input-A Signal Sel.” setting on the SET SETTING menu. • Use the composite sync signal when you input the external sync signal from video GBR/component equipment. Connecting the Projector Each time you press the key, the input signal switches as follows: Projecting Input-AtInput-BtVideotS-Video APA FREEZE KEY STONE /TILT LENS AUTO FOCUS PIC MUTING AUDIO MUTING INPUT ENTER RESET D ZOOM VOLUME MENU VPL-CX63 ON/STANDBY indicator Rear remote control detector To input from Press INPUT to display Computer connected to the INPUT A connector Input-A Computer connected to the INPUT B connector Input-B Video equipment connected to the VIDEO input connector Video Video equipment connected to the S VIDEO input connector S-Video Projecting the Picture Smart APA (Auto Pixel Alignment) adjusts the picture of the connected equipment so that it is projected clearly. Notes • If “Auto Input Search” is set to “On,” the projector searches for the signals from the connected equipment and displays the input channel where the input signals are found. For details, see “Auto Input Search” on page 29. • The Smart APA feature is effective for the input signal from a computer only. 5 Switch the equipment connected to output to the projector. Depending on the type of your computer, for example a notebook, or an all-in-one LCD type, you may have to switch the computer to output to the projector by pressing certain keys (e.g., , etc.), or by changing your computer’s settings. LCD / VGA / , 1 Plug the AC power cord into a wall outlet, then connect all equipment. The ON/STANDBY indicator lights in red and the projector goes into standby mode. 2 Press the ?/1 key. The ON/STANDBY indicator flashes in green. 3 Turn on the equipment connected to the projector. 4 Press the INPUT key to select the input source. Projecting F7 Fx Fn or and F7 Fx Fn or and Note The key used for switching the computer to output to the projector varies depending on...
Este manual também é adequado para os modelos :Projetores - VPL-CX63 (1.22 mb)