Assessments - 2, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
If the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and then perform Fine Adjustment again. ► It is only enabled for the PC Timing input of the D-Sub terminal. ► Refer to " PC Timing (D-Sub/HDMI) 1) Auto Adjustment : Used to adjust frequency and phase of PC screen automatically. 2) Coarse : Used to adjust frequency when vertical lines appear on PC screen. 3) Fine : Used to fine tune the PC screen. 4) Reset : Using this function, you can reset the PC menu settings to the factory default settings. oo oo Auto Adjustment oo Coarse Fine oo Reset Zoom Enlarges the PC screen to 2X, 4X, or 8X. ► This can only be adjusted when the input signal is PC Timing(D-Sub/HDMI). | Basic Functions | Input | Picture | Setup | Option | £ Setup * Click the Play(<3)/Stop({J) button in the table below to view the video file. Description Play/Stop Adjustment Install To tailor the picture to the installation location, you can invert the projected images vertically/horizontally. 1) Front-Floor : Normal Image oo 2) Front-Ceiling : Horizontal/Vertical Reversed Image 3) Rear-Floor : Horizontally Reversed Image Lamp Mode V-Keystone Background Test Pattern Video Type Reset 4) Rear-Ceiling : Vertically Reversed Image Used to set the image brightness by adjusting the amount of light generated by the lamp. 1) Eco : This mode is optimized for small screens smaller than 100 inches. This mode decreases the lamp brightness and power consumption in order to extend the lamp lifetime and reduce noise and power consumption. 2) Normal : This mode is optimized for general use. This mode is the recommended mode for a stable lamp brightness that enables a low-noise, comfortable operating environment even under bright ambient illumination. 3) Bright : This mode maximizes the lamp brightness when the ambient illumination is bright. As the brightness of the lamp increases, the lamp lifetime can be reduced and the noise and power consumption may increase. If video scences are distorted or tilted, you can compensate for this using the vertical Keystone function. You can set the Background that is displayed when there is no signal from the external device connected to the projector.If a signal is received, the Background you set disappears and a normal screen is displayed. 1) Logo 2) Blue 3) Black Generated by the projector itself. Utilized as standard to optimize the installation of the projector. 1) Crosshatch : You can check whether the picture is distorted or not. 2) Screen Size : You can refer to picture format sizes such as 1.33:1 or 1.78:1. If the screen quality is abnormal since the projector does not identify the input signal type automatically in PC or HDMI mode, you can set the input signal type by force. ► In [PC] mode, this is only enabled if the input signal is AV Timing(D-Sub).However, for a separate H/V sync., this is only enabled for the 1280 x 720p 59.94 Hz/60 Hz signals. ► In [HDMI] mode, this is only enabled for the 640x480p 59.94Hz/60 Hz, 1280x720p 59.94Hz/60 Hz signals from among the AV Timing(HDMI) signals. 1) Auto 2) RGB(PC) 3) RGB(AV) 4) YPbPr(AV) Usage Color, Sharpness,Tint PC menu and zoom RGB(PC) When connecting the RGB output of a PC to the D-Sub terminal Disable Enable RGB(AV) When connecting the RGB output of an AV device (STB, DVD, etc---) to the D-Sub terminal Enable Enable YPbPr(AV) When connecting the YPbPr output of an AV device (STB, DVD, etc-) to the D-Sub terminal Enable Disable PC When connecting a PC to the HDMI terminal Disable Enable AV When connecting an AV device (STB, DVD, etc-) to the HDMI terminal Enable Disable Auto Auto settings - - 90 Eco OO Normal OO Bright oo •• oo Crosshatch oo Screen Size oo Using this function, you can reset various settings to the factory default settings. 1) Factory Default : Changes the settings to the factory defaults. oo Factory Default 2) Reset Filter Time : Resets the filter time. oo Reset Filter Time | Basic Functions | Input | Picture | Setup | Option | * Click the Play(9)/Stop(Q) button in the table below to view the video file. Screen Adjustment Language Description You can select the Language used for the menu screen. 1) English 7) Svenska 2) Deutsch 8) Portugués 3) Nederlands 9) Русский 4) Español 10) "Ыи 5) Français 11)ФШт§ 6) Italiano i2) Play/Stop Menu Option Sound 1) Position You can move Menu Position up/down/left/right. 2) Transparency You can set the translucency of menu. - Low - Medium - High - Opaque 3) Display Time You can set the display time of the menu. - 5 sec / 10 sec / 30 sec / 60 sec / 90 sec / 120 sec / Stay On Adjusts the right and left audio balance and equalizer of the 3W stereo speaker embedded in the projector. 1) Balance 2) 100Hz 3) 300Hz 4) 1kHz 5) 3kHz 6) 10kHz 90 Position о о Transparency OO Display Time Filter Check Time Sets the check period for the filter. (Unit: hour) 1) Off Auto Power...
Este manual também é adequado para os modelos :Projetores - SP-L300 (2.12 mb)