Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Enter community name (read only). Default name is "public". Trap Item Description Community name....................... Enter community name to send "Trap". Default name is "public". Trap address.................................... Enter IP address of the SNMP manager computer to receive "Trap". Trap check/delete Check and delete the trap address Checking the registered trap address and deleting the address. To delete the address, tick check box in front of the IP address and click Delete button. . Up to 10 trap addresses can be registered. Trap option Trap option setting Tick check boxes in front of the condition item to send the trap. . Click Set button if you tick or un-tick the check box on a page. . "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. . Up to 99,999 hours can be set for the time setting. 4 Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. Chapter 4 Controlling the Projector Power control and status check Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled. Confirmation window as shown in the below appears when the Standby button is pressed. Popup confirmation window Item Description PJ status Power .......................... Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status .......................... Displays the status of the projector's power. (Refer to next page.) Power control......... Controls the projector power by clicking the "ON" or "Standby" button. . The projector cannot be turned on while the projector is on cooling down. . The web browser checks and updates the projector's condition every 30 seconds automatically. Power control and status check About projector condition Status Description Normal................................................................Projector is operating normally. Power management in operation............Power management is operating Lamp failure....................................................Lamp failure is occurring Abnormal Temperature..........................The temperature of the projector became too high Standby after Abnormal Temp.......... Projector detects abnormal temp. and sets into standby mode. Power failure ................................................. Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control the projector through the network, unlock the security on the projector using with the projector's menu control. Caution about turning on/off the projector via the networks When turning on/off the projector via the networks, preset the projector as follows: 1. Select “Setting” from the Projector menu. 2. Select “Standby mode” from the Setting menu and set it as “Network”. If you set this function as "Network", the network part of the projector is constantly provided with power even if the projector is turned off. If you set this as Eco, then the network part will be turned off when you turn off the projector. Consequently, you cannot turn on/off the projector via the networks. Control Click Control on the main menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. . Please see the user's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode. Item Description Input.......................... Selects input mode of the projector. Source...................... Selects signal source of the input. COMPUTER 1 : ANALOG PC COMPONENT SCART COMPUTER 2 : ANALOG PC VIDEO S-VIDEO . The control page displays valid control items depending on the selected input mode, signal or functions of the projector you use, therefore, there may be different controls between the described items and actual control items on the page display. For further information , refer to the projector's user's manual. . When the projector is in standby, all the controlling items are inactive. Control System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available selection at the ANALOG PC input Item Description XGA1......................... It automatically switches to the proper c...