Assessments - 1, GPA: 3 ( )

Fabricante : Toshiba Arquivo Tamanho: 2.4 mb Arquivo Nome : Língua de Ensino:

Should this occur, reduce the refresh rate of the computer signal, or lower the resolution. Use of connection cables that are 2 m or shorter is recommended. • The input signal specifications of the DVI port of the projector conform to DVI 1.0 specifications; however, contents protection is not supported. Note that there is no guarantee for the operations not specified in this specification. Connecting video equipment CONTENTS You can project the picture from video equipment by using VIDEO IN connectors. Check that the power supplies for the projector and for the video equipment are off before connecting the cables. USB COMPUTER IN 1 COMPUTER IN 2 S-VIDEOVIDEO VIDEO IN R - AUDIO - L AUDIO IN ( Y/PB/PR ) MONITOR OUT CONTROL Pin plug (red) To audio output (R) To S-VIDEO connector Be sure to connect in the proper direction. To S-video output Pin plug (white) To audio output (L) Pin plug (yellow) To video output (Red) To AUDIO-R jack S-video cable (not supplied) Video equipment AV cable (supplied) (Yellow) To VIDEO jack (White) To AUDIO-L jack Installation and connections Note The S-VIDEO connector and VIDEO jack can be used independently, but the audio input jacks are used as both the S-VIDEO and VIDEO input. Continued Connecting video equipment (continued) CONTENTS You can project the picture from video equipment with component video output jack. Check that the power supplies for the projector and for the video equipment are off before connecting the cables. USB COMPUTER IN 1 COMPUTER IN 2 S-VIDEOVIDEO VIDEO IN R - AUDIO - L AUDIO IN ( Y/PB/PR ) MONITOR OUT CONTROL 45 Video equipment (DVD player, etc.) COMPUTER IN 1 connector For use as both analog RGB(1) and Y/PB/PR input. At shipping from factory, it is set for use as analog RGB(1) input. Change the setting on the menu when using as Y/PB/PR input. AUDIO IN jack For use as both audio signals for RGB input (analog RGB (1)/analog RGB (2)/digital RGB) and Y/PB/PR input. Pin plug (red) To audio output (R) To AUDIO IN jack To COMPUTER IN 1 connector Be sure to connect in the proper direction. Adapter BNC-pin (Not supplied) Audio cable (not supplied) Monitor cable Mini D-sub 15P-BNC (Not supplied) Pin plug (white) To audio output (L) (Blue) To PB video output (Green) To Y video output (Red) To PR video output Installation and connections Projector operation control by a computer CONTENTS You can control the projector by a computer connected with the control cable supplied. 73 Check that the power supplies for the projector and for the computer are off before connecting the cables. USB COMPUTER IN 1 COMPUTER IN 2 S-VIDEOVIDEO VIDEO IN R - AUDIO - L AUDIO IN ( Y/PB/PR ) MONITOR OUT CONTROL Computer Remove the cover to use the CONTROL connector. To RS-232C port Control cable (supplied) To CONTROL connector Be sure to connect in the proper direction. To remove the cover, slide it up while pushing it. Installation and connections Note Do not connect any cable other than the exclusive one supplied. How to use the output connector CONTENTS You can output video signals to a computer monitor, etc. Check that the power supplies for the projector and for the equipments are off before connecting the cables. USB COMPUTER IN 1 COMPUTER IN 2 S-VIDEOVIDEO VIDEO IN R - AUDIO - L AUDIO IN ( Y/PB/PR ) MONITOR OUT CONTROL To MONITOR OUT connector Be sure to connect in the proper direction. Computer monitor, etc. Installation and connections Notes • The analog RGB signals or Y/PB/PR signals of the COMPUTER IN 1 or COMPUTER IN 2 connector selected by the input select operation are output from the MONITOR OUT connector. If neither of these input sources is selected, the signal of the COMPUTER IN 1 connector is output. (Digital RGB signals are not output.) • Signals are output from the MONITOR OUT connector even when in the standby mode. • An ordinary computer monitor may not display a normal picture with Y/PB/PR signals. Projection on the screen CONTENTS CAUTION – Do not look into the projection lens while operating the projector. Remote control 1 MENU ON/STANDBY INPUT L-CLICK R-CLICK ENTER KEYSTONE AUTO SET EXIT PIP FREEZE MUTECALL RESIZE VOLUME/ADJUST LASER Control panel KEYSTONE AUTOSET EXIT ON / STANDBY VOL / ADJ ENTER MENU INPUT FANTEMPLAMPON 1 1 Indicators (Main unit side) Preparation Install and connect the projector properly. Take off the lens cover. 1 2 Operations Press ON/STANDBY. The projector turns on and the ON, LAMP and FAN indicators light in green. (The LAMP indicator blinks while the lamp is warming up.) The lamp lights and the start up display appears. ON / STANDBY FANTEMPLAMPON ON / STANDBY FANTEMPLAMPON (Green) (Green) (Green) (Green) (Green)(Green Flashing) 1 ON/STANDBY ON/STANDBY Notes • The startup screen disappears when you push the EXIT button or wait for a while. You can also set the startup screen not to be displayed on the menu screen. 51 • When a projector is used for the first time, the language selection menu is displayed after the startup screen disappears...

Baixe o seu

Para fazer o download, introduza 2 dígitos :