Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The ON/STANDBY indicator lights in red and the projector goes into standby mode. 2 Press the I / 1 key. The ON/STANDBY indicator lights in green. 3 Turn on the equipment connected to the projector. 4 Press the INPUT key to select the input source. To input from Press INPUT to display Computer connected to the INPUT A connector INPUT A Video equipment connected to the video1) input connector VIDEO 1) If you connect to both the S VIDEO and VIDEO jacks, the signal from the S VIDEO jack is selected. 21GB Projecting 5 Turn the zoom ring to adjust the size of the picture. 6 Turn the focus ring to adjust the focus. Caution Looking into the lens when projecting may cause injury to your eyes. To adjust the volume Press VOLUME +/– keys on the control panel. To control the computer using the supplied Remote Commander When you connect an IBM PC/AT compatible to the projector, you can control the mouse of the computer using the Remote Commander. The R/L CLICK keys and joystick function as follows. Key and joystick Function R CLICK (front) Right button L CLICK (rear) Left button Joystick Corresponds with the movements of the mouse Note Make sure that nothing obstructs the infrared beam between the Remote Commander and the remoter control detector on the projector. To get the clearest picture You can adjust picture quality when projecting a signal from the computer. 1 Project a still picture from the computer. 2 Press the APA key. “Complete!” appears on the screen when the picture is adjusted properly. Notes • Press the APA key when the full image is displayed on the screen. If there are black edges around the image, the APA function will not function properly and the image may extend beyond the screen. • When you switch the input signal or re-connect a computer, press the APA key again to adjust the picture again. • You can cancel the adjustment by pressing the APA key again while “ADJUSTING” appears on the screen. • The picture may not be adjusted properly depending on the kinds of input signals. • Adjust the items in the INPUT SETTING menu when you adjust the picture manually. GB 22 Projecting To turn off the power 1 Press the I / 1 key. “POWER OFF? Please press I / 1 key again.” appears to confirm that you want to turn off the power. Note A message disappears if you press any key except the I / 1 key, or if you do not press any key for five seconds. 2 Press the I / 1 key again. The ON/STANDBY indicator flashes in green and the fan continues to run for about 90 seconds to reduce the internal heat. Also, the ON/STANDBY indicator flashes quickly for the first 30 seconds. During this time, you will not be able to turn the power back on with the I / 1 key. 3 Unplug the AC power cord from the wall outlet after the fan stops running and the ON/STANDBY indicator lights in red. When you cannot confirm the on-screen message When you cannot confirm the on-screen message in a certain condition, you can turn off the power by holding the I / 1 key for about one second. Note Do not unplug the AC power cord while the fan is still running; otherwise, the fan will stop even though the internal heat is still high, which could result in a breakdown of the projector. To stow the leg on the bottom If you are not going to use the projector, close the front cover first and then fold up the leg on the bottom of the projector manually at the end. On air filter To maintain optimal performance, clean the air filter every 300 hours. Setting Up and Projecting 23GB Projecting B Adjustments and Settings Using the Menu Using the MENU The projector is equipped with an on-screen menu for making various adjustments and settings. You can perform all of the menu operation with the control panel on this unit. Also, you can change the menu language displayed in the on-screen menu. To change the menu language, see “Selecting the Menu Language” on page 19. 1 Press the MENU key. The menu appears. The menu presently selected is shown as a yellow button. 80 50 PICTURE CTRL CONTRAST: BRIGHT: GAMMA MODE: GRAPHICS COLOR TEMP: HIGH INPUT-A 2 Use the M or m key to select a menu, then press the , or ENTER key. The selected menu appears. Menus Setting items SET SETTING STATUS: ON INPUT-A: RGB KEYSTONE MEMORY: OFF DIGITAL KEYSTONE: OFF LANGUAGE: ENGLISH POWER SAVING: OFF SIRCS RECEIVER: FRONT&REAR LAMP TIMER: 00010h INPUT-A 3 Select an item. Use the M or m key to select the item, then press the , or ENTER key. 4 Make the setting or adjustment on an item. • When changing the adjustment level: To increase the number, press the M or , key. To decrease the number, press the m or < key. Press the ENTER key to restore the original screen. • When changing the setting: Press the M or m key to change the setting. Press the ENTER or < key to restore the original screen. To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Press the RESET key. “Complete!” appears on the screen and the...