Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
phono plug) cable (not supplied) A/V connecting adaptor (supplied) abcAudio (stereo audio connecting cable (not supplied))* Use a no-resistance cable. * Connect only when you want to output the audio from the speaker of the projector. Projecting Projecting Before connecting the equipment, plug the AC power cord into a wall outlet. a Press the I/1 (on/standby) key. b Turn on the computer connected to the projector. c Press the INPUT key to select the input source. d When the computer is connected, set it to output the video signal to only the external monitor. ENU AC IN Fn FxF7 PowerOn/Stand by2211 4433 INPUT or and Input A Video S-Video Projecting Adjusting the Projector a Adjust the position of the picture. b Adjust the size of the picture. c Adjust the focus, as required. TILT ZOOM– + FOCUS– + 2211 33 FOCUS AUTO or Turning off the Power a Press the I/1 (on/standby) key. b When a message appears, press the I/1 (on/standby) key again. c Unplug the AC power cord from the wall outlet after the fan has stopped running and the ON/STANDBY indicator has lit in red. Notes The internal circuitry of the Off & Go function may cause the fan to continue to operate for a short time even after the I/1 key is pressed to turn off the power and the ON/STANDBY indicator changes to red. 11 2233 Projecting Replacing the Lamp The lamp used as a light source is a consumable product. Thus, replace the lamp with a new one in the following cases. • When the lamp has burnt out or dims • “Please replace the Lamp.” appears on the screen • The LAMP/COVER indicator lights up The lamp life varies depending on conditions of use. Use an LMP-C163 Projector Lamp as the replacement lamp. Use of any other lamps than the LMP-C163 may cause damage to the projector. Caution The lamp remains hot after the projector is turned off with the ?/1 key. If you touch the lamp, you may burn your finger. When you replace the lamp, wait for at least an hour for the lamp to cool. Note Be sure that the projector is stable after turning it over. 3 Open the lamp cover by loosening the three screws with a Phillips screwdriver. Notes • If the lamp breaks, contact your Customer Information Center. • Pull out the lamp by holding the handle. If you touch the lamp, you may be burned or injured. • When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while it is tilted and if the lamp breaks, the pieces may scatter, causing injury. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet. Note When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool. 2 Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can see its underside. Note For safety reasons, do not loosen any other screws. 4 Loosen the two screws on the lamp unit with the Phillips screwdriver (a). Fold out the handle (b), then pull out the lamp unit by the handle (c). Fold out the handle. Replacing the Lamp 5 Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (c). Fold down the handle to replace it (b). Fold down the handle. Notes • Be careful not to touch the glass surface of the lamp. • The power will not turn on if the lamp is not secured properly. 6 Close the lamp cover and tighten the three screw. Note Be sure to attach the lamp cover securely as it was. If not, the projector cannot be turned on. 7 Turn the projector back over. 8 Connect the power cord. The ON/STANDBY indicator around the ?/1 key lights in red. 9 Press the following keys on the Remote Commander in the following order for less than five seconds each: RESET, b, B, ENTER. Caution Do not put your hands into the lamp replacement slot, and do not allow any liquid or other objects into the slot to avoid electrical shock or fire. Disposal of the used lamp For the customers in the USA Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (Replacing the Lamp Cleaning the Air Filter The air filter should be cleaned every 500 hours. Remove dust from the outside of the ventilation holes with a vacuum cleaner. 500 hours are approximate. This value varies depending on the environment or how the projector is used. When it becomes difficult to remove the dust from the filter with a vacuum cleaner, remove the air filter and wash it. 1 Turn the power off and unplug the power cord. 2 Place a protective sheet (cloth) beneath the projector and turn the projector over. 3 Remove the air filter cover. 4 Remove the air filter. Claws 5 Wash the air filter with a mild detergent solution and dry it in a shaded place. 6 Attach the air filter so that it fits into the each claws (6 positions) on the air filter covers and replace the cover. Notes • If you neglect to cle...
Este manual também é adequado para os modelos :Projetores - VPL-CX21 (2.8 mb)