Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
c Adjust the sound with the VOLUME +/– key on the Remote Commander or adjust “Volume” in the PICTURE SETTING menu (see page 32). Remote Commander/Presentation tool Symptom Cause and Remedy The Remote Commander does not work. • The Remote Commander batteries are dead. c Replace with new batteries (see page 17). • The COMMAND ON/OFF switch is set to OFF. c Set to ON. • The PJ/NETWORK selector switch is set to NETWORK. c Set to PJ. The computer cannot be • The USB cable is not connected. controlled with the Remote c Connect the projector to the computer using the USB cable. Commander. • You are operating the Air Shot (VPL-CX75 only). c When using the Air Shot, the computer cannot be controlled with the Remote Commander. The computer cannot be • The USB cable is used. controlled with the • The Air Shot is not used. presentation tool (VPLc The presentation tool is designed to use with the Air Shot. CX75 only). Use the Remote Commander to operate the device connected via the USB cable. Others 47 47 GB Troubleshooting Others Symptom Cause and Remedy The control panel keys do not function. • The control panel keys are locked. c Unlock the control panel keys (see page 36). Indicators Symptom Cause and Remedy The LAMP/COVER indicator flashes. • The lamp cover or the air filter cover is detached. c Attach the cover securely (see page 43 and 44). • The lens protector does not open due to a problem. c Slide the lens protector by hand, and then press the I/1 key. The LAMP/COVER indicator lights up. • The lamp has reached the end of its life. c Replace the lamp (see page 42). • The lamp becomes a high temperature. c Wait for 60 seconds to cool down the lamp and turn on the power again. The TEMP/FAN indicator flashes. • The fan is broken. c Consult with qualified Sony personnel. The TEMP/FAN indicator lights up. • The internal temperature is unusually high. c Check to see if nothing is blocking the ventilation holes. • The projector is used at a high altitude. c Ensure that “High Altitude Mode” in the INSTALL SETTING menu is set to “On.” Both the LAMP/COVER and TEMP/FAN indicators light up. • The electrical system breaks down. c Consult with qualified Sony personnel. Messages List Warning Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy High temp.! Probably use in high altitude. Switch to high altitude mode on? Yes V No v • Internal temperature is too high. c When using the projector at an altitude of 1,500 m or higher, set “High Altitude Mode” in the INSTALL SETTING menu to “On” (see page 39). c If this message appears on the screen when using the projector at normal altitudes, check to see if anything is blocking the ventilation holes (exhaust). High temp.! Lamp off in 1 min. • Internal temperature is too high. c Turn off the power. c Check to see if nothing is blocking the ventilation holes. GB 48 Troubleshooting Message Meaning and Remedy Frequency is out of range! • This input signal cannot be projected as the frequency is out of the acceptable range of the projector. c Input a signal that is within the range of the frequency. • The resolution setting of the output signal of a computer is too high. c Set the setting of output to XGA (see page 20). Please check Input-A Signal Sel. • You have input RGB signal from the computer when “Input-A Signal Sel.” in the SET SETTING menu is set to “Component.” c Set “Input-A Signal Sel.” correctly (see page 35). Please replace the LAMP. • It is time to replace the lamp. c Replace the lamp. Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! • You have pressed the wrong key. c Press the appropriate key. The panel keys are locked ! • “Panel Key Lock” in the INSTALL SETTING menu is set to “On.” c All the keys on the control panel of the projector are locked. Operate the projector with the keys on the Remote Commander (see page 36). 49 49 GB Troubleshooting Others Specifications Optical characteristics Projection system 3 LCD panels, 1 lens, projection system LCD panel 0.79-inch XGA panel, about 2,360,000 pixels (786,432 pixels . 3) Lens 1.2 times zoom lens (powered) f 23.5 to 28.2 mm/F1.6 to 1.78 Lamp 165 W UHP Projection picture size 40 to 300 inches (measured diagonally) Light output ANSI lumen1) 2500 lm (VPLCX75) ANSI lumen1) 2000 lm (VPLCX70) (When the Lamp Mode is set to “High”) Throwing distance (When placing on the floor) When the XGA signal is input 40-inch: 1.2 to 1.4 m (3.9 to 4.6 feet) 80-inch: 2.4 to 2.7 m (7.9 to 8.9 feet) 100-inch: 3.0 to 3.4 m (9.8 to 11.2 feet) 150-inch: 4.5 to 5.2 m (14.8 to 17.1 feet) 200-inch: 6.0 to 6.9 m (19.7 to 22.6 feet) 250-inch: 7.5 to 8.7 m (24.6 to 28.5 feet) 300-inch: 9.0 to 10.4 m (29.5 to 34.1 feet) There may be a slight difference between the actual value and the design value shown above. 1) ANSI lumen is a measuring method of American National Standard IT 7.228. Electrical charact...
Este manual também é adequado para os modelos :Projetores - VPL-CX75 (3.07 mb)