Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Pressing the f on the TILT adjustment key or M/, key on the Remote Commander, the more the projector tilts and the higher the position of the picture. Pressing the F on the TILT adjustment key or m/< key on the Remote Commander, the less the projector tilts and the lower the position of the picture. V Keystone Corrects the trapezoidal distortion caused by the projection angle. Select “Auto” for automatic correction, or “Manual” for manual correction using the < or , key. When the bottom of the trapezoid is longer than the top : Sets a lower value. When the top of the trapezoid is longer than the bottom : Sets a higher value. Note The auto V Keystone adjustment may not correct the trapezoidal distortion perfectly, depending on the room temperature or the screen angle. Even when projecting using “Side Shot”, the four sides of a picture may sometimes not be parallel to the respective sides of a screen frame. Image Flip Flips the image on the screen horizontally and/or vertically. Off: The image does not flip. HV: Flips the image horizontally and vertically. H: Flips the image horizontally. V: Flips the image vertically. Background Select the background color of the screen when no signal is input to the projector. Select “Black” or “Blue”. Normally, set to “Blue.” Test Pattern The factory setting is “Off.” When set to “On,” a test pattern is displayed on the screen during the “Lens Zoom” adjustment, “Lens Focus,” “Side Shot” or “V Keystone.” If you do not want to display a test pattern, set to “Off”. Lamp Mode Sets the lamp brightness in the projection. Adjustments and Settings Using the Menu 35 35 GB The INSTALL SETTING Menu High: Illuminates the projected image brightly. Standard: Reduces fan noise and power consumption. The brightness of the projected image will be lower compared with the “High” setting. Direct Power On Set to “On” if you are using a circuit breaker to turn the power on/off the entire system. You can turn off the power just by unplugging the power cord without pressing the I/1 key. Lens Control When set to “Off,” the LENS (FOCUS, ZOOM) key on the Remote Commander, and the FOCUS and ZOOM keys on the projector do not function. High Altitude Mode The factory setting is “Off.” Set to “On” when the projector is used at an altitude of 1,500 m or higher. Security Lock Turns on the projector’s security lock function. Off: Turns off the security lock function. On: Turns on the security lock function, which locks the projector once a password has been set. For details, see “Security Lock” on page 24. The INFORMATION Menu The INFORMATION menu displays the horizontal and vertical frequencies of the input signal and the used time of the lamp. Memory number of an input signal Input A fH: 48.47kHz fV : 60.00Hz No.23 Lamp Timer: 0H INFORMATION Signal type Menu Items fH Displays the horizontal frequency of the input signal. The displayed value is approximate. fV Displays the vertical frequency of the input signal. The displayed value is approximate. Lamp Timer Indicates how long the lamp has been turned on. Note These only display on the screen. You cannot alter the display. GB 36 The INFORMATION Menu B Maintenance projector over so you can see its Maintenance underside. Note Replacing the Lamp Replace the lamp with a new one in the following case. • When the lamp has burnt out or dims • “Please replace the LAMP.” appears on the screen • The LAMP/COVER indicator lights up The lamp life varies depending on conditions of use. Use LMP-C190 Projector Lamp as the replacement lamp. Use of any other lamps than the LMP-C190 may cause damage of the projector. Caution The lamp becomes a high temperature after turning off the projector with the I / 1 key. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least an hour for the lamp to cool. Notes • If the lamp breaks, consult with qualified Sony personnel. • Pull out the lamp by holding the handle. If you touch the lamp, you may be burned or injured. • When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while tilted and if the lamp breaks, the pieces may scatter, causing injury. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet. Be sure that the projector is stable after turning it over. 3 Open the lamp cover by loosening a screw with the Phillips screwdriver. Note For safety sake, do not loosen any other screws. Maintenance Note When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool. 2 Place a protective sheet (cloth) beneath the projector. Turn the 37 37 GB Maintenance 4 Loosen the two screws on the lamp unit with the Phillips screwdriver (1). Fold out the handle (2), then pull out the lamp unit by the handle (3). Handle 5 Insert the new lamp all the way in until it is securely in place (1). Tighten the two screws (2). Hold down the handle to replace (3). Notes • Be careful not to touch...