Fabricante : Sony
Arquivo Tamanho: 2.37 mb
Arquivo Nome :
|
Facilidade de uso
2) VGA, SVGA, XGA and SXGA are registered trademarks of the International Business Machines Corporation, U.S.A. 3) NTSC4.43 is the color system used when playing back a video recorded on NTSC on an NTSC4.43 system VCR. 4) DDCTM is a registered trademark of the Video Electronics Standard Association. 8 (GB) Location and Function of Controls 1 Zoom ring Location and Function of Adjusts the size of the picture. Controls 2 Focus ring Front/Left Side 2 3 6 45 7 1 qa qs 0 8 9 Rear/Right Side/Bottom w; qg qjqh qk qd qf ql Adjusts the picture focus. 3 Lens Open the lens cap before projection. 4 Ventilation holes (exhaust) 5 Front remote control detector (SIRCS receiver) 6 Adjuster When a picture is projected on the out of the screen, adjust the picture using this adjuster. For details on how to use the adjusters, see “How to use the adjuster” on page 10 (GB). 7 Security lock Connects to an optional security cable (Kensington’s). The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact Kensington 2853 Campus Drive, San Mates, CA 94403 U.S.A. Tel: 800-535-4242: extension 3348 Home page address: 8 Carrying handle Pull up the handle from the projector for carrying. 9 Left speaker 0 Control panel For details, see “Control panel” on page 11 (GB). qa Right speaker qs Lens hood qd Rear remote control detector (SIRCS receiver) qf AC IN socket Connects the supplied AC power cord. 9 (GB) Location and Function of Controls qg Rear speaker qh Lamp cover qj Ventilation holes (intake)/air filter cover Notes • Do not place anything near the ventilation holes as it may cause internal heat build-up. • Do not place your hand or objects near the ventilation holes — the air coming out is hot. qk Air filter cover button Used to remove the air filter cover. For details, see “Cleaning the Air Filter” on page 33 (GB). Note Clean the air filter every 300 hours to ensure optimal performance. ql Adjuster buttons w; Connector panel For details, see page 12 (GB). How to use the adjuster To adjust the height Adjust the height of the projector as follows: 1 Lift the projector and press the adjuster buttons. The adjusters will extend from the projector. Adjuster buttons 2 While pressing the buttons, lower the projector. Then, release the buttons. For fine adjustment, turn the adjusters to the right and the left. Notes • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the adjusters out. 10 (GB) Control panel INPUT HELPMENU ENTER RESET APA LIGHT VOL + VOL - LAMP/ COVER TEMP/ FAN POWER SAVING ON/ STANDBY 56789 1234 qa 0 1 VOL +/– keys Adjust the volume of the built-in speakers and output level of the AUDIO jack. + : Increases the volume. – : Decreases the volume. 2 Arrow keys (M/m/,) Used to select the menu or to make various adjustments. 3 MENU key Displays the on-screen menu. Press again to clear the menu. 4 HELP key If you need help information during an operation, press this key to display help messages. The Help menu lists error recoveries depending on problem type. 5 Indicators LAMP/COVER: Lights up or flashes under the following conditions: • Lights up when the lamp has reached the end of its life or becomes a high temperature. • Flashes when the lamp cover or air filter cover is not secured firmly. TEMP (Temperature)/FAN: Lights up or flashes under the following conditions: • Lights up when temperature inside the projector becomes unusually high. • Flashes when the fan is broken. POWER SAVING: Lights up when the projector is in the power saving mode. When POWER SAVING in the SET SETTING menu is set to ON, the projector goes into the power saving mode if no signal is input for 10 minutes. Although the lamp goes out, the cooling fan keeps running. In the power saving mode, any key does not function for the first 40 seconds. The power saving mode is canceled when a signal is input or any key is pressed. ON/STANDBY: Lights up or flashes under the following conditions: • Lights in red when the AC power cord is plugged into the wall outlet. Once in the standby mode, you can turn on the projector with the I / 1key. Location and Function of Controls • Lights in green when the power is turned on. • Flashes in green while the cooling fan runs after turning off the power with the I / 1key. The fan runs for about 120 seconds after turning off the power. The ON/STANDBY indicator flashes quickly for the first 40 seconds. During this time, you cannot turn the power back on with the I / 1key. For details on the LAMP/COVER and the TEMP/FAN indicators, see page 35 (GB). 6 I / 1(on / standby) key Turns on and off the projector when the projector is in the standby mode. The ON/STANDBY indicator lights in green when the power is turned on. When turning off the power, press the I / 1key twice following the message on the screen, or press and hold the key for about one second. For details on steps for turning off the power, see...
Este manual também é adequado para os modelos :Projetores - VPL-PX30 (2.37 mb)
- ()
- ()