Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
35.82/0.9055) – 72.99} . 1.025 a (maximum) = {(SS . 43.834/0.9055) – 54.66} . 0.975 b = x – (SS/0.9055 . 6) c = x – (SS/0.9055 . 6 + 158.3) Installation 33 (GB) Unsuitable Installation Unsuitable Installation Do not install the projector in the following situations. These installations may cause malfunction or damage to the projector. Poorly ventilated • Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. When the internal heat builds up due to the block-up, the temperature sensor will function with the message “High Temperature! Power off in 1 min.” The power will be turned off automatically after one minute. • Leave space of more than 30 cm (11 7/8 inches) around the unit. • Be careful that the ventilation holes may inhale tininess such as a piece of paper. Highly heated and humid • Avoid installing the unit in a location where the temperature or humidity is very high, or temperature is very low. • To avoid moisture condensation, do not install the unit in a location where the temperature may rise rapidly. Very dusty Avoid installing the unit in a location where there is a lot of dust; otherwise, the air filter will be obstructed. The dust blocking the air through the filter may cause raising the internal heat of the projector. Clean it up periodically. 34 (GB) 35 (GB) Notes on Installation No toppling of the unit Avoid using as the unit topples over on its side. It may cause malfunction. Use to be level Do not install the unit other than on the floor. Avoid using as the unit tilts to one side or tilts upward or downward more than 20 degrees. These installation may cause malfunction. No blocking the ventilation holes Avoid using something to cover over the ventilation holes; otherwise, the internal heat may build up. Carry out the followings. 20° 20° UVW`aJKLMN Maintenance Maintenance Replacing the Lamp When it is time to replace the lamp, replace the lamp promptly with a new LMP-600 Projector Lamp. When replacing the lamp after using the projector Turn off the projector, then unplug the power cord. Wait for at least an hour for the lamp to cool. Note The lamp will still be very hot after turning off the power. Wait until the lamp has cooled completely before replacing. 1 Place a protective sheet (cloth) beneath the projector. Turn the projector over so it is upside down. Note Be careful not to topple over the projector after turning it over. 2 Pull out the adjuster by pressing the adjuster button and turn it outward. 3 Open the lamp cover by loosening two screws with the Philips screwdriver (supplied with the LMP-600 Projector Lamp). For safety sake, do not loosen the other screws. 4 Loosen the screw on the lamp unit with the Philips screwdriver. Pull out the lamp unit by the handle. 5 Insert the new lamp all the way in until it is securely in place. Tighten the screw. Fold down the handle. Notes • Be careful not to touch the glass surface of the lamp. • The power will not turn on if the lamp is not secured properly. 6 Close the lamp cover and tighten the screws. 7 Turn the adjuster inward and push it back. 8 Turn the projector back over. 9 Connect the power cord and turn the projector to the standby mode. 10Press the following keys on the control panel in the following order for less than in five seconds each: LIGHT, ?, /, ENTER. 36 (GB) Maintenance Notes • The lamp becomes a high temperature after turnig off the projector with the I /ukey. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least an hour for the lamp to cool. • Be sure to use the LMP-600 Projector Lamp for replacement. If you use lamps other than LMP-600, the projector may cause a malfunction. • Be sure to turn off the projector and unplug the power cord before replacing the lamp. • Do not place the old lamp near children or near the objects which catch fire easily. • Do not get wet the lamp or fall any liquid or object inside the lamp. The lamp may broken. • Do not put your hands into the lamp replacement spot, or not fall any liquid or object into it to avoid electrical shock or fire. Cleaning the Air Filter The air filter should be cleaned every 300 hours. When it becomes difficult to remove the dust from the filter, replace the filter with a new one. To clean the air filter, follow the steps below: 1 Turn off the power and unplug the power cord. 2 Pull up the carrying handle. 3 Press and hold the PUSH button and remove the air filter cover on the right side of the projector. 4 Pull up the spring. ................................................................................................................................................................................................................................................................................ 5 Remove the air filter. ................................................................
Este manual também é adequado para os modelos :Projetores - VPL-SC60M (2.08 mb)
Projetores - VPL-SC60U (2.08 mb)