|
por este dispositivo também tem outras instruções :
Facilidade de uso
Resets the value of an item to its factory preset value or returns the enlarged image to its original size. This key functions when the menu or a setting item is displayed on the screen. m D ZOOM (Digital Zoom) +/– key Enlarges the image at a desired location on the screen. n M/m/, keys (Arrow) o MENU/TAB key Functions as a MENU key. p APA (Auto Pixel Alignment) key Automatically adjusts a picture to its clearest while a signal is input from a computer. For details, see “Smart APA” in “The SET SETTING Menu” on page 29. q VOLUME +/– keys r LENS key Each time you press this key, the Focus adjustment and Zoom adjustment menus are displayed alternately. s PJ NETWORK (Projector/ Network) selector switch Normally, set to “PJ.” t COMMAND ON/OFF switch When this switch is set to OFF, the keys on the Remote Commander do not function. This saves battery power. u Infrared transmitter To install batteries 1 Push and slide the lid to open it, then install the two size AA (R6) batteries (supplied) with the correct polarity. While pressing the lid, slide it. Be sure to install the battery from the # side. 2 Replace the lid. Location and Function of Controls Presentation Tool (VPL-CX76 only) You can use a laser pointer or control a presentation file made using Microsoft PowerPoint when projecting a picture using the Air Shot feature. a Laser transmitter b LASER key A laser beam is emitted from the laser transmitter while you keep this key pressed. c SLIDE G/g key Used to change pages of the slide show in the forward/backward direction. d B key This key corresponds to the “B” key of a keyboard. When you press this key during the slide show, a black screen is displayed. To cancel the black screen, press this key again. language of the operating system (OS) of your computer. To install the batteries Open the cover (b) with a coin (a) and remove the battery case (c). Install the two size AAA (R03) batteries with the correct polarity. Notes on the laser beam • Do not look into the laser transmitter. • Do not aim the laser at people. Notes on Remote Commander/ Presentation tool operation • Make sure that nothing obstructs the infrared beam between the Remote Commander/Presentation tool and the remote control detector on the projector. Direct the Remote Commander/ Presentation tool toward the front or rear remote control detector. • The operation range is limited. The shorter the distance between the Remote Commander/Presentation tool and the projector is, the wider the angle within which the commander can control the projector becomes. Overview Note A black screen may not be displayed even if you press the “B” key depending on the Location and Function of Controls B Projecting the Picture Installing the Projector The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide. Distance between the screen and the center of the lens Screen Unit: m (feet) Screen size (inches) 40 80 100 150 200 250 300 Minimum 1.2 2.4 3.0 4.5 6.0 7.5 9.0 Distance (3.9) (7.9) (9.8) (14.8) (19.7) (24.6) (29.5) Maximum 1.4 2.7 3.4 5.2 6.9 8.7 10.4 Distance (4.6) (8.9) (11.2) (17.1) (22.6) (28.5) (34.1) There may be a slight difference between the actual value and the design value shown in the table above. Installing the Projector To connect a computer Connecting the Projector When you connect the projector, make sure to: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals. When pulling out a cable, be sure to pull it out by the plug, not the cable itself When connecting to a wireless LAN using the Air Shot, see “Operating Instructions for Air Shot” stored on the CD-ROM (VPLCX76 only). Connecting a Computer This section describes how to connect the projector to a computer. For more information, refer to the computer’s instruction manual. Projecting the Picture AUSB cable (supplied)(Connect the USB cable to use a wireless mouse.) BHD D-sub 15-pin cable (supplied) CStereo audio connecting cable (not supplied) (Use a no-resistance cable.) AUDIO STD/DUO S VIDEO INPUT A VIDEO 123to USB connector Left side to monitor output Computer to audio output Notes • The projector accepts VGA, SVGA, XGA, SXGA, and SXGA+ signals. However, we recommend that you set the output mode of your computer to XGA mode for the external monitor. • If you set your computer, such as a notebook computer, to output the signal to both your computer’s display and the external monitor, the picture of the external monitor may not Connecting the Projector appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the operating instructions supplied with your computer. Note To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor. USB f...
Este manual também é adequado para os modelos :Projetores - VPL-CX70 (1.07 mb)