Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Projetores - P5207B (1.22 mb)
Projetores - P5207B (1.86 mb)
Projetores - P5207B (4.21 mb)
Projetores - P5207B (1.39 mb)
Facilidade de uso
Make sure the projector has been cooled down for at least 45 minutes before changing the lamp. Warning: Lamp compartment is hot! Allow it to cool down before changing lamp! To remove the lamp: Turn the projector off by pressing (POWER). Allow the projector at least 45 minutes to cool down. Disconnect the power cord. 1 Use a screwdriver to remove the screw from the cover. (Illustration #1) 2 Push up and remove the cover. 3 Remove the lamp protection film (Illustration #2). 4 Remove the screw that secures the lamp module (Illustration #3). 5 Pull out the lamp connector from a slot in the lamp compartment. Disconnect it from the projector (Illustration #4). 6 Lift the handle so that it stands up (Illustration #5). Pull out the lamp module by force (Illustration #6). To replace the lamp module, use a new lamp and reverse the above steps (Illustrations # - # ). Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. 1 12 1 12 6 5 7 8 8 10 9 4 3 1 2 1 2 2 11 7 12 38 English Ceiling Mount Installation If you wish to install the projector using a ceiling mount, please refer to the steps below: 1 Drill four holes into a solid, structurally sound part of the ceiling, and secure the mount base. Note: Screws are not included. Please obtain the appropriate screws for your type of ceiling. 2 Secure the ceiling rod using the appropriate type of cylinder screws. 20 mm 13 mm 8.4 mm 130 mm 49.9 mm Short Rod Screw Type A 50 mm length / 8 mm diameter - Ceiling Mount Base - Attach to ceiling Long Rod Extension Rod Allen Key - For tighten/loosen Tightening Screw Medium Rod Large Cylinder Cap 39 English 3 Use the appropriate number of screws for the projector size to attach the projector to the ceiling mount bracket. Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Use two washers for extra support, if deemed necessary. 4 Attach the ceiling bracket to the ceiling rod. Smaller Washer Large Washer Projector Bracket Supports projector and allows for adjustments Screw Type B Spacer - For heat dissipation Sliding Extension Screw Type C Screw Type A 50 mm length - /8 mm diameter Large Cylinder Cap Allen Key - For tighten/loosen Tightening Screw En gl ish 40 5 Adjust the angle and positioning as necessary. 30 Allen Key Tightening Screw Allen Key Tightening Screw Note: The appropriate type of screw and washer for each model is listed in the table below. 3 mm diameter screws are enclosed in the screw pack. Models Screw Type B Washer Type Diameter (mm) Length (mm) Large Small P5207B/N217E/PN-X15K/P5207i/ N217R/ PN-X15F/P5307WB/N227E/PN-W15K/ P5307Wi/N227R/PN-W15F 3 25 V V 149.5 mm 242.04 mm Screw M3 Depth 9.5 mm 41 Specifications The specifications below are subject to change without notice. For final specs, please refer to Acer's marketing documentation. Projection system DLP™ Resolution • P5207B/N217E/PN-X15K/P5207i/ N217R/PN-X15F: Native: XGA (1024 x 768) Maximum: UXGA (1600 x 1200), 1080p (1920 x 1080) • P5307WB/N227E/PN-W15K/P5307Wi/N227R/PNW15F: Native: WXGA (1280 x 800) Maximum: UXGA (1600 x 1200), 1080p (1920 x 1080), WUXGA (1920 x 1200) (supports reduce blanking only) Computer compatibility Refer to the "Compatibility Modes" section for more information. Video compatibility NTSC (3.58/4.43), PAL (M/N), PAL 60, SECAM, HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i, 576i) Aspect ratio • P5207B/N217E/PN-X15K/P5207i/ N217R/PN-X15F: Auto, 4:3, 16:9 • P5307WB/N227E/PN-W15K/P5307Wi/N227R/PNW15F: Auto, 4:3, 16:9, Full, Letter Box Displayable colors 1.07 billion colors Projection lens F = 2.59 - 2.87, f = 16.88 mm - 21.88 mm, 1:1.3 Manual Zoom and Manual Focus Projection screen size (diagonal) • P5207B/N217E/PN-X15K/P5207i/ N217R/PN-X15F: with clear focus 44" (111 cm) - 230" (584 cm) • P5307WB/N227E/PN-W15K/P5307Wi/N227R/PNW15F: 45" (115 cm) - 300" (762 cm) Projection distance with clear • P5207B/N217E/PN-X15K/P5207i/ N217R/PN-X15F: focus 3.3' (1 m) - 26.2' (8 m) • P5307WB/N227E/PN-W15K/P5307Wi/N227R/PNW15F: 4.9' (1.5 m) - 19.7' (6 m) Throw ratio • P5207B/N217E/PN-X15K/P5207i/ N217R/PN-X15F: 70"±3% @ 2 m (1.41 - 2.25 : 1) • P5307WB/N227E/PN-W15K/P5307Wi/N227R/PNW15F: 82.5"±3% @ 2 m (1.12 - 1.8 : 1) Horizontal scan rate 31 - 99 KHz Vertical refresh scan rate 23 - 120 Hz Keystone correction +/-40 Degrees (Vertical), Manual Digital zoom 2 X Audio 5W x 2 Weight Approximate 3.5 kg (7.72 lbs.) English Dimensions (W x D x H) 290 x 254 x 99 mm (11.4" x 10" x 3.9") Power supply Universal AC input 100 - 240 V, input frequency 50/60 Hz English 42 Power consumption (typical) 460 W Operating temperature 0.C to 40.C / 32.F to 104.F I/O connectors • Power socket x 1 • RS232 x 1 • VGA input x 2 • VGA output x 1 • Composite video x 1 • S-Video x 1 • 3.5 mm audio jack input x 2 • 3.5 mm audio jack output x 1 • HDMI x 2 • RJ45 LAN input x 1 • USB (Type mini B) x 1 • ...
Este manual também é adequado para os modelos :Projetores - P5307WB (2.65 mb)