Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
• Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • NOTE: Read entire instruction sheet before you start installation and assembly. NOTE: Read entire instruction sheet before you start installation and assembly. • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Never exceed the Maximum Load Capacity. See page one. • If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended. • Always use an assistant or mechanical lifting equipment to safely lift and position equipment. • Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. • Carriage box has over 100 lbs (43 kg) of pressure. Be careful not to pinch fingers. • This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. • This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet. To mount this product to an alternative supporting surface, contact Peerless customer care at 1 800 865-2112. • This product was designed to be installed on the following wall construction only; WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED x Wood Stud None Wood Beam None x Solid Concrete None x Cinder Block None x Metal Stud Do not attach except with Peerless accessory kit for metal studs; Contact Customer Service for Peerless accessory kit for metal studs. Brick Contact Customer Service Other or unsure? Contact Customer Service Tools Needed for Assembly • stud finder ("edge to edge" stud finder is recommended) • phillips screwdriver • drill • 1/4" bit for concrete and cinder block wall • 1/2" bit for metal stud wall • 5/32" bit for metal or wood stud wall • level 2 of 16 ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 Visit the Peerless Web Site at For customer care call 1-800-865-2112 or 708-865-8870. ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 Visit the Peerless Web Site at For customer care call 1-800-865-2112 or 708-865-8870. 3 of 16 G Before you begin, make sure all parts shown are included with your product. B C A D H J K L M N O P Q E F I CARRIAGE R S T Parts may appear slightly different than illustrated. Description Qty. Part # A wall mount assembly 1 055-1841 B projector tube 1 055-1839 C projector arm 1 055-1830 D adapter plate 1 055-1828 E hook bracket 2 055-1840 F vertical handle 2 055-1834 G horizontal handle 1 055-1858 H projector adapter plate 1 055-1822 I slide plate 1 055-1821 J projector mount 1 PRG-1 K #10-32 x 0.375" phillips screw 18 520-1130 L M6 x 12 mm serrated washer head socket pin screw 8 510-1050 M 0.25"ID spacer 4 590-1050 N 1/4-20 x 1.0" hex head screw 2 520-1606 O #10-32 x 3/8" serrated washer head socket pin screw 2 520-1151 P 0.25" ID nylon washer 4 540-9460 Q #14 x 2.5" wood screw 6 5S1-015-C03 R acorn nut 2 530-1049 Splug 1 590-1303 T #10-32 x 1-3/8" socket pin screw 2 510-1098 U alligator anchor 6 590-0097 V 5/32" (4 mm) security allen wrench 1 560-9646 W #10-32 x 1/4" socket pin screw 2 520-1196 X flanged bushing 1 590-1271 Y retainer bushing 1 055-1836 Z cable tie 6 560-9711 toggler pack 1 ACC615 Parts List ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 Visit the Peerless Web Site at For customer care call 1-800-865-2112 or 708-865-8870. 4 of 16 1 Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes. Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart below. FLOOR PROJECTOR SCREEN A Parts List Continued U V X BOTTOM OF SCREEN W X Y TOP MOUNTING HOLES Screen Size Dimension X 63" 36" 77'' 42" CHART Z ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 Visit the Peerless Web Site at For customer care call 1-800-865-2112 or 708-865-8870. 5 of 16 Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Fasten two #14 x 2.5" wood screws (Q) into top mounting holes leaving a .25" of exposed thread as shown. Hook wall mount assembly ...