Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. Indicates that the power plug is to be disconnected Contact Premier Mounts with any questions – from the power outlet. 800-368-9700. Safety precautions must be taken at all times. Warning and Caution statements. A secure structure must support the weight, or load, of the projector. When mounting to a ceiling that contains wooden studs, dead center of the wooden stud must be confirmed prior to installation. Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the projector and/or damage to the mounting surface. Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the projector and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the projector. Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Installation Manual Page -2 - PBM-070L Installation Manual Page - 3 - Parts List This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts 800-368-9700. Base Box (Qty 1) Projector Bracket(Qty 1) Jam Nut (Qty 1) M6 x 6mm Set Screw (Qty 1) Nylon Spacers (Qty 2) .” Flat Washers (Qty 2) M6 x 12mm Phillips Head Screws (Qty 6) Projector Bracket Hardware M8 x 12mm Phillips Head Screws (Qty 8) Installation Tools Soft Material/Blanket Portable Drill M3 Allen Wrench (Supplied) Pencil Finder (Commercially Available) Level Tape Measure Phillips Head Screw Driver Ladder PBM-070L Installation Manual Page - 4 - Projector Bracket Installation M8 x12mm Phillips Head Screws Projector Bracket Projector Screwdriver M8 x12mm Phillips Head Screws Step 1. Invert the projector and place it on a soft and flat surface. Remove any foot levelers that might possibly prevent the correct installation of the bracket. Step 2. Locate the eight mounting points located on the bottom of the projector. Step 3. Line up the mounting points on the projector with the mounting holes on the mounting bracket. Step 1. Using a screwdriver, secure the mounting bracket using eight (8) M8 x 12mm Phillips Head screws. Do not over-tighten these screws. Over-tightening the screws may result in damaging the threaded inserts on the projector. PBM-070L Installation Manual Page - 5 - Ceiling Installation Step 1. Separate the top bridge from the base box by removing the six (6) M6 x 12 mm screws that are located on the base box, three on each side (A). Step 2. Secure the top bridge to the ceiling structure at this time (see warning label) using commercially available hardware (B). Step 3. Use the two (2) middle slot openings for single wood stud mounting. All other mounting points on the top bridge may be used depending on your installation application (B). Step 4. Replace the base box to the secured top bridge and secure with the six M6 x 12 mm screws (C). Base Box Lag Bolts (Commercially Available) Ceiling Structure Wood Stud Top Bridge A B C PBM-070L Page - 6 - Installation Manual Step 5. Loosely install the hinge pin screws, flat washer and nylon spacer to each side of the base box. Step 6. Slide the nylon spacer and the flat washer to the back of the screws. Step 7. Raise the mounting bracket and attached projector to the base box and insert the hinge-pins through the hinge-pin openings. Step 8. Tighten the hinge pin screws. Step 9. Determine the viewing angle. Once the viewing angle has been determined, insert and tighten the four (4) tilt locking screws. Do not over-tighten the screws. Ceiling Structure Top Bridge Hinge Pin Bolt FlatWasher Tilt Locking Screws Wood Stud PBM-070L Page - 7 - Installation Manual If installing a PBM-070L from the ceiling structure, please refer to the installation instructions that are included with those mounts. Step 10. Install the jam screw all the way up to the end of the threads of the threaded PBM-070L. Step 11. Screw in the 1." bridge opening to the PBM-070L all the way up to the jam screw. Step 12. Tighten the jam screw and the base box together. Step 13. Loosely install the hinge pin screws, flat washer and conical spacer to each side of the base box. Step 14. Slide the conical spacer and the flat washer to the back of the screws. Step 15. Raise the projector mount, attached to the projector’s chassis, and insert the hinge-pins through the hinge-pin openings. Step 16. Raise the rear of the projector and install the four (4) M6 x 12 mm tilt locking screws to the rear of the base box; adjust the til...