Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Produced by BARCO NV,Nov. 2007. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v. Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco at the web: Printed in Belgium Safety guidelines WHO WARNING CAUTION PRODUCT CARE This installation manual must be performed by authorized technical personnel only. The ceiling should be capable of supporting a weight of at least 5 times the total weight of the Ceiling Mount and Projector (i.e. at least 160 kg or 353LB). If it cannot, the ceiling must be reinforced. Improper installation may result in serious personal injury. Consult a professional structural engineer prior to suspending the Ceiling Mount from a structure not intended for that use. Always ensure the working load limit of the structure supporting the Ceiling Mount. Installing the Ceiling Mount should be performed only after you are thoroughly familiar with all of the following safety checks and installation instructions. To do otherwise increases the risk of hazards and injury to the user. This support is designed for intended use only with Barco CLM series projectors. It supports maximum 33 kg or 73LB. Use with any other appliance/projector may result in instability causing possible injury. Do not modify and/or replicate any component. Barco n.v. uses specific materials and manufacturing processes in order to achieve part strength. Consult Barco nv for assistance with custom applications. Always follow Barco installation instructions. Contact Barco n.v. if you should have any question regarding the safety of an application. Ceiling Mount components should be kept dry, clean, lubricated (if required), coated properly, and otherwise maintained in a manner consistent with part design. Barco products must be used in a manner consistent with their design and inspected on a routine basis for security, wear, deformation, corrosion and any other circumstances that may affect the load handling capability of the part. Barco n.v. recommends inspections at least once a year for all installations and increasing in frequency for more critical installations. If the part is found to have damage, which may cause a decrease in load capability, the part must be removed from service immediately. Under no circumstances are Barco parts repariable by anyone other than Barco n.v. Description and Contents of the kit Purpose of the Kit The kit is designed for the CLM CM R10 series projectors and allows the projector to be mounted to the ceiling. Contents of the Kit Following items are included: • Kit R9849999: Ceiling mount • Installation manual : R59770182 • Mounting bracket and Screws: R835785 Qty 3 Nos and R 826743 qty 1 No, - -- • Safety Chain set : B361213 Qty 1 Nos , A577535 qty 1 Nos, A566050 qty 1 nos and B363509 qty 2 nos • Cable cover assy Illustration of the ceiling mount R826743 R835786 R83578 Remark: The ceiling mount can also be mounted using one of the 2 available bars (height adjustment) and cable cover assy. R9841260: short bar R822922 and cable cover assy . min length = 445mm(17.52 inch) max length = 810 mm(31.89 inch) R9841261: long bar R822923 cable cover kit R984 . min length = 845mm(33.27 inch) max length = 1210 mm(47.64 inch) I llustration of the Cable Cover Assy: Note: The assembly is used only when ceiling mount is mounted along with IQ bar for hiding and guiding the cables. R826748 Mounting the Assembly Necessary Tools 1. Torx screw driver for M3 screw 2. Hexagonal driver (n° 6) 3. Ring spanner 12-13mm 4. Side spanner 12-13mm 5. Cross head screw driver for M8 screw Centering the ceiling mount Mark the position on the ceiling hole. Since the center of the lens does not coincide with the center of the projector, the center of the lens has been marked on the ceiling mount. Remark The horizontal shift of the ceiling mount allows to re-enter the projector later on, However, centering decently the base plate insures a good horizontal shift margin afterwards. Mounting the Assembly The fixation can be done with standard M8 bolt (not supplied) Washer , Spacer M10 R835785 and Flange Nut M8 Projector preparation 1. Turn the projector to its back and remove the Feet assembly. Unscrew 3 Plastic feet and remove their Allen head M10 screws. Discard 3 plastic feet r852944 and x head M10 screw. 2. Fix the Spacer M10 (r835785) as shown below. For alignment of the Centre distance between the spacers fix the ceiling mount and fix nut M8 B360623, Do not tight fully then tight the spacer M10. Remove the Ceiling mount and fix it on the Ceiling. R852944, R852945 & A566050 M10 SCREW, & FEET SUPPORT 3. Lift and slide the projector assembly into the Ceiling mount. The projector will be located precisely into the ceiling mount base plate after the tightening of 3 M 8 flange Nuts (b360623). 4. Route the Signal cables and Power cord into the cable saddles. 5. Take care of the orientation of safety chain bracket. 6. Fix t...