Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
make sure this surface faces front FIGURE 1 Install the base box to the LiteMount False Ceiling Plate surface faces front false ceiling plate make sure this surface faces front false ceiling plate make sure this FIGURE 2 Install the base box to the LiteMount Pipe Tubing Extension Attach the Mounting Plate to the Projector CAUTION: Use only the hardware that is provided with the LP 425 Ceiling Mount. Using different hardware may damage your projector. Attach the Mounting Plate to the Projector 1 Set the projector on a table with the bottom side up. 2 Insert the 2 screws into the 2 quick release sleeves. 3 Loosely attach the screws and sleeves to the holes in the projector as shown in Figure 3. 4 Align the keyholes in the mounting bracket with the screws in the projector. Slide the mounting bracket until the quick release sleeves are at the top of the keyhole slot. 5 Attach the 8 mm knurled knob to the projector in the location shown in Figure 3. Tighten the two 8 mm screws and the 8 mm knurled knob. Be careful not to over-tighten the screws. knurled knob quick release sleeves goes here FIGURE 3 Attach the mounting plate to the projector Hang the Projector on the Ceiling 1 Loosely install the 12 mm knurled knobs, flat washers, and conical spacers to the 2 hinge pins on the base box (Figure 4). slide projector bracket here between the base box and the spacer knurled knob spacer washer FIGURE 4 Attach knurled knobs to the side of the base box 2 Make sure your cables are pulled through the center hole of the base box, then carefully lift the projector and turn it upside down so the mounting plate faces the ceiling (Figure 5). 3 Insert the projector and mounting bracket slots onto the base box hinge pins between the spacers and base box (Figure 4). Slide the projector bracket forward until the hinge pins rest fully in the vertical slots and support the projector. Hang the Projector on the Ceiling FIGURE 5 Install the projector in the ceiling base box 4 Insert the remaining two 12 mm knurled knobs through the rear slots in the mounting bracket and into the threaded holes on the sides of the base box. Insert knurled knob through this slot screen FIGURE 6 Insert the knurled knobs to adjust the angle 5 Adjust the angle of the projector so that it will project correctly. Refer to your LP 425 User’s Guide for detailed information on projection angles and image sizes. 6 Tighten all the knurled knobs to secure the projector in position. 7 Check all fasteners to make sure they are properly tightened. 8 Connect the power cord and the cables to the projector. (Refer to your LP 425 User’s Guide for information about connecting the cables.) Inverting the Image When you need to remove the projector or replace the lamp: 1 Disconnect all cables. 2 Hold the projector from underneath. 3 Remove the knurled knob that holds the projector to the mounting plate. 4 Slide the projector to release it from the quick release bolts. The projector will come off of the mounting plate. The mounting plate will still be attached to the base box. 5 Replace the lamp as described in your LP 425 User’s Guide if needed. 6 Realign the quick release bolts in the keyhole slots on the mounting plate. 7 Fasten the knurled knob. ADJUSTING THE IMAGE Inverting the Image 1 Press the Menu button on the keypad to display the projector’s on-screen menu. 2 Using the arrow buttons, move the cursor to the Controls tab to display the Controls menu. 3 Move the cursor to Ceiling, then click either mouse button. Limited Warranty In Focus Inc. warrants that each “ceiling mount” sold hereunder will conform to and function in accordance with the written specifications of In Focus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. The product may contain recycled components that are in new condition. Said warranty shall continue for a period of one (1) year from the date of such purchase. Proof of purchase is required for all warranty claims. In Focus does not warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. In Focus’ liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at In Focus’ sole option. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to In Focus, and must be protected by packaging comparable to the original packaging. The Product must be accompanied by a written letter that includes (i) proof of date of purchase, (ii) the dealer’s name, (iii) the part number of the accessory item or the projector/panel model number, (iv) your business card information, (v) explanation of how the item was damaged, and (vi) description of the damage and reason for the r...