Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Please also read Part 1 – Important Product Information. 1 AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones. © 2000 Advanced American Telephones. All rights reserved. Printed in Mexico. 850002775 Issue 1AT&T 5/00 USER’S MANUAL Part 2 I N S T A L L A T I O N RING SELECT MSG ALERT POWER Battery Installation (optional) ANNC SELECT Telephone Line Cord For Table/Desk Installation 1 Install the batteries. • Turn the unit upside down. • Push in on the two tabs at the large end of the base, and lift the base off the unit. • Push in on the two tabs on the battery compartment door, and remove it. • Insert four AA batteries. Always use four new batteries. • Replace the battery compartment door. • Reattach the base by inserting the tabs into the slots. Push down on the large end of the base to lock it into place. Make sure the larger end is toward the top of the telephone. The telephone should sit flat on your table or desk during use. NOTE: The batteries provide backup power, allowing you to make calls in case of a power failure. When battery power is low, the LOW BATTERY light goes on. Replace the batteries promptly. 2 Connect the line cord to the telephone. Plug one end of the line cord into the jack labeled TEL LINE on the bottom of the telephone. Run the line cord through the channel on the bottom of the phone. 3 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, then hang up. 4 Connect the line cord to a wall jack. Plug the free end of the line cord into a telephone wall jack. Make sure the cord snaps firmly into place. 5 Connect the power cord. Fit the power cord behind the strain relief tab. Then, plug the smaller end of the power cord into the jack labeled POWER on the back of the system. Plug the power cord into an electrical outlet not controlled by a wall switch. (When you connect the system to power, the Message Window flashes CL to indicate you need to set the clock. See “Setting the Clock” in the ANSWERING SYSTEM OPERATION section of this manual.) 1 INSTALLATION Reverse the Handset Tab 321 T TPULL TABS TO OPEN T T Figure 1 Figure 2 For Wall Installation 1 Reverse the handset tab. (This tab holds the handset when you hang up.) Hold down the switchhook, and slide the tab up and out of its slot. Turn the tab so that the end with the “hook” is up. Then insert the tab back into its slot. 2 Remove the base. Push in on the two tabs at the large end of the base, and lift the base off the unit. 3 Install the batteries. • Push in on the two tabs on the battery compartment door, and remove it. • Insert four AA batteries. Always use four new batteries. • Replace the battery compartment door. NOTE: The batteries provide backup power, allowing you to make calls using the handset in case of a power failure. When battery power is low, the LOW BATTERY light goes on. Replace the batteries promptly. 4 Wrap the line cord around the posts on the inside of the base. Leave at least three inches free at each end of the line cord (Figure 1). 5 Attach the base. Turn the base so the larger end of the base is toward the bottom of the telephone. Attach the base by inserting the tabs into the slots indicated. Push down on the large end of the base to lock it into place (Figure 2). Figure 3 Figure 4 6 Connect the line cord to the telephone. Plug one end of the line cord into the jack labeled TEL LINE on the bottom of the phone (Figure 3). 7 Connect the line cord to the wall jack, and mount the phone on the wall. Plug the free end of the line cord into the modular wall jack. Make sure the cord snaps firmly into place. Place the phone on the wall jack mounting studs and pull down until it is held securely (Figure 4). 8 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, then hang up. 9 Connect the power cord. Plug the smaller end of the power cord into the jack labeled POWER on the back of the system. Plug the power cord into an electrical outlet not controlled by a light switch. (When you connect the system to power, the Message Window flashes CL to indicate you need to set the clock. See “Setting the Clock” in the ANSWERING SYSTEM OPERATION section of this manual.) 2 IN CASE OF DIFFICULTY If this telephone does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 222–3111. No Dial Tone • Make sure all plugs are connected properly. Check the line cord connections at the wall jack and at the telephone. Also check the coiled cord connections to the handset at both ends. • Unplug the telephone and connect it to another wall jack. If you still have no dial tone, the problem is with your phone line. Call your local telephone service provider. • If the system is not connected to AC power and batteries are not installed, you...