Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
The intercom is compatible with various Chamberlain Wireless Products. Features On/Off: To turn intercom ON, press Talk button. To turn intercom OFF, hold down the Volume DOWN button for 3 seconds. Talk Button: Following the ringing of the doorbell by a guest, press and hold the Talk button to talk to the guest. Once the link to the doorbell is made, any other intercoms in the network cannot hear the conversation. Volume: Pressing the Volume DOWN button will lower the volume and pressing the Volume UP button will increase the volume. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use. When batteries are low intercom will emit three beeps every ten minutes. A DC Adapter (not provided) can also be used to power the intercom. In this case, the channel lights will remain on. Models NDIS and NDISC WIRELESS DOORBELL AND INTERCOM ® INTERCOM DOORBELL Call Button: To talk, press and release the Call button and all intercoms in the network will receive the signal. When holding down the Talk button on a different intercom, a secure channel is created and the other intercoms in the network do not hear the conversation. Once a secure link is made, the Call button on the doorbell does not need to be pressed to speak again. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use. (Lithium batteries recommended for colder environments.) Alternate Chimes: The doorbell can be set to ring with two different chime patterns, to identify which doorbell is signaling. To change chime pattern, set Dipswitch #2 to the UP position. Volume: To increase the doorbell volume, set Dipswitch #4 to the UP position. Sensitivity: To increase sensitivity on the doorbell set Dipswitch #3 to the UP position. MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 HOLD ACTIVE TALK 1 3 2 4 VOLUME MONITOR CHANNEL OFF Mounting Tape Alcohol Wipe MONITOR HOLD OFF 1 3 2 4 VOLUME TAL K ACTIVE Volume UP Button Talk Button Learn Button Dipswitch #1 Dipswitch #2 AC Adapter Channel Select Button Channel Lights Active Light Volume DOWN Button Monitor Button Speaker OPTIONAL Voice Activation Mode (VOX): Voice Activation Mode (VOX) allows a call to be answered without pressing the Talk button. Once a call is heard on an intercom which has been set to VOX, a response can be given by speaking loudly into the intercom. There will be a slight delay when VOX is first activated by a voice, but will continue to transmit audio until the speaking stops. To put intercom into VOX, place Dipswitch #1 to the UP position. While in VOX mode, a call may be initiated by pressing the Talk button. Rubber Pads Intercom 1 2 Doorbell 2 Assemble Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) DOORBELL Program Intercom to Doorbell Press the Learn button on the intercom until a beep is heard. Mount Doorbell Mount doorbell with small silver screws. Screw the top two screws halfway into the mounting surface. Place back of doorbell over screws. Tighten screws. The doorbell can be mounted by using the included screws or by using the double-sided mounting tape. It is recommended to use the mounting tape on surfaces such as metal or glass. MOUNTING WITH SCREWS Put the remaining silver screws into the bottom holes of doorbell. Tighten screws. MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE Within 10 seconds press the Learn button on the doorbell until a beep is heard. Peel off white paper from mounting tape. Firmly press mounting tape on back of doorbell. Peel paper from mounting tape. Firmly press doorbell onto mounting surface. Clean back of doorbell and mounting surface using the alcohol wipe. MOUNTING WITH TAPE Secure cover with the two large black screws. Secure Cover 1 2 INTERCOM Install 4 AA Alkaline batteries (not provided). Adhere rubber pads to bottom. Repeat Steps 1 and 2 for any additional intercoms. 1 2 1 1 2 1 2 3 1 3 ADD TO AN EXISTING NETWORK Press the Learn button on the new intercom until a beep is heard. Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. Repeat for any additional intercoms. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate Press and release the Talk network and the memory will need to be cleared. button to verify network is complete. VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 Operation Talk Button: To talk, hold down the Talk button. All intercoms in the network that are on the same channel will receive the signal. Release the Talk button when done talking and within 10-15 seconds press and hold the Talk button of a different intercom to make a secure channel between the two. Once the channel is made the other intercoms in the network cannot hear the conversation. Channel Button: Press the Channel button to set intercom to one of four secure c...
Este manual também é adequado para os modelos :Telefones com fio - NDISC (1.7 mb)