Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
The MUGAPLM is compatible with various LiftMaster Wireless Products. Multi-Unit Gate Access Panel (MUGAPLM) Bolt (4) Washer (4) Nut (4)Key (2) Telephone Interface Unit (OTIU): The OTIU allows the user to identify which gate or door a visitor is at with Caller ID and a distinctive ring tone. To answer a call press “0”. A gate can be opened by dialing “*9” on the telephone keypad. Accessory Overview Portable Intercom: The intercom allows the user to speak with visitors at the MUGAPLM and open the gate by holding the Remote button for 10 seconds. Flush Mount Intercom: The intercom allows the user to speak with visitors at the MUGAPLM. Repeater Set: Repeaters are used to extend the range between the MUGAPLM and other devices. They are recommended for use with buildings with stucco or cement walls. Remote Control Transmitter: The remote control transmitter will open the gate when the numbered button is held down for 5 seconds within 75' of the MUGAPLM. Multi-Unit Telephone Interface (MUOTIU): The MUOTIU acts as a wireless remote autodialer in a dedicated line system. MUGAPLM Installation & Assembly Step 1 Choose mounting location for MUGAPLM. Remove the back panel and attach it to a solid surface or post. Step 2 Install 4 C batteries (not provided) in the MUGAPLM and it will beep until the Master PIN Number is entered. Step 3 On keypad press: Step 4 Enter 4 digit Master PIN Number. Example: 1234. Step 5 Mount the MUGAPLM onto the back panel. Lock MUGAPLM with key. NOTE: Do not slam the MUGAPLM against the wall or the temper sensor will activate. If additional MUGAPLM is being used see Operation & Features: Multi-GAP Mode. ? ? NOTE: “ * “ is a cancel button that will cancel any call or key sequence. “BEEP” “BEEP” NOTE: To prevent damage to the circuit DO NOT use C size Lithium batteries or rechargeable batteries. If Lithium batteries are needed, switch the C battery pack with the provided AA battery pack. # # # ? ? 1 2 Gate Control Unit (GCU) (not provided) Assemble Step 1: Remove GCU cover. Step 2: Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) NOTE: This step applies only if more than one GCU is being used. Step 3: Up to four GCUs can be used. Each GCU will need a different Identity. Set the Identity of the GCU by changing the Dipswitches as shown in the chart below. GCU ID Switch #1 Switch #2 1 OFF OFF 2 ON OFF 3 OFF ON 4 ON ON Dipswitches Learn Button Program Press the Learn button on the GCU for one second. The LED will light for 20 seconds. LED ? ? ? ? Within 20 seconds enter Master PIN Number on MUGAPLM: Followed by GCU Identity as determined in Step 3: 1 OR 2 OR 3 OR 4 The GCU LED will blink 3 times indicating programming is successful. NOTE: The relay will engage. If error tone is heard or GCU LED emits 3 double blinks, then programming has failed. Repeat for additional GCUs. Installation Step 1: Replace GCU cover and mount near gate operator control box. Step 2: Remove bottom panel of GCU. Connect Terminal 10 on GCU to Common on gate operator (shown below). Connect Terminal 9 to Cycle on gate operator (shown below). “BEEP” “BEEP” NOTE: If there is already an existing receiver proceed to Pre-Installed LiftMaster Receiver (315Mhz Only) section. 1 2 3 4 5 6 7 8 9 10 11 DC AC + - COM N/C EXIT SAFETY EDGE COMMON OPEN GATE OPERATOR N/O GCU Step 1: Press and release the Learn button on the intercom. Step 2: Within 20 seconds enter Master PIN Number on MUGAPLM. Step 3: Press “05”. Step 4: Followed by (00-63) Step 5: Then press the Call Button. Intercom will beep indicating programming is successful. When the Call button is pressed on the MUGAPLM, the intercom will beep for 40 seconds. During this time, the intercom will ONLY connect to the MUGAPLM. Hold down the Talk button on the intercom to speak to the visitor. Release the Talk button to hear the response. This will be a secure conversation and other intercoms will be locked out. The intercom can also display Gate Status and be put into Conference Mode by changing the Switch Settings. For complete installation and operating instructions refer to Portable Intercom manual. Portable Intercom Pre-Installed LiftMaster Receiver (315Mhz Only) Step 1: Pry open the front panel of the receiver case with a coin or a screwdriver. Step 2: Press and release the Learn button on the receiver. The Indicator Light will light for 30 seconds indicating that receiver is in Learn Mode. Step 3: Within 30 seconds enter Master PIN Number on GAPLM. Step 4: Press “1”. The Indicator Light on the receiver will blink 3 times indicating programming is successful. NOTE: An error tone will be heard for 3 consecutive activations only. After the third activation the MUGAPLM assumes that the GCU has been replaced with the receiver. Repeat Steps 2-4 for each remote, or control device that will be used to access the LiftMaster door or gate operator. Program Indicator Light Learn Button Erase All Control Codes Press and hold the Learn butt...