Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Once the screws are fully loosened, (they will not come all the way out), slide the doors in the direction of the arrows. 3. Insert 4 AA-size alkaline batteries as shown on the diagram in the battery compartments. Two batteries will be inserted for each compartment. 4. Replace the battery compartment doors securely and tighten the screws, being careful not to strip the threads. 5. If the cords were previously connected, re-attach the line cords to the unit and check your memory locations. NOTE: If the low battery icon LOW appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation. During the replacing of batteries, a backup circuit in the unit will retain your stored information for up to 60 seconds. Write down any stored information you do not want erased. IMPORTANT: If you’re not going to use the telephone for more than 30 days, remove the batteries because they can leak and damage the unit. SETTING UP THE CALLER ID MENU You should not plug the telephone into the wall line jack while setting up the Caller ID menu. An incoming call may invalidate the change if it was not yet saved. The phone must display “xx CALLS” before you can enter the setup menu. 1. Press and release the REVIEW up button then hold down the REVIEW down button. “SETUP MENU ^ v” appears. 2. At this point you can press either REVIEW up or down button to scroll among the 6 menu screens, which are: • SETUP MENU ^ v • LOCAL AREA CODE (default - - -) • CID LANGUAGE (default English) • LCD CONTRAST (default 3) • T/P DIAL MODE (default tone) • EXIT SETUP 3. You have 10 seconds following any key press before the phone will automatically return to the “CALLS” summary screen. CALLER PHONE 10/1912:30 1 - 315 - 555 - 1324 SMITH JOHN delete dial review TO SET YOUR LOCAL AREA CODE The telephone uses the programmed area code to determine the number format to display when a valid Caller ID signal is received and is also used for the Dialback feature. 1. Press and release the REVIEW up button then hold down the REVIEW down button. “SETUP MENU ^ v” appears. 2. Press the REVIEW up button until “LOCAL AREA CODE” appears. 3. To enter or change the area code, press the DELETE button. The display shows the present area code stored. The left-most digit or a minus sign (-) flashes, indicating it is ready to accept the area code entry. 4. Press REVIEW down to choose 9-0 for the first digit. 5. When the desired digit is flashing, press REVIEW up to advance to the next digit. 6. Repeat steps 1 and 2 until all the digits for your area code are correct. If you make a mistake, you can simply retrace the previous steps until your area code is set. 7. Press DIAL to store the area code and return to the “LOCAL AREA CODE” display. TO SET THE CID DISPLAY LANGUAGE This adjustment changes the Caller ID prompts to be displayed in English, French or Spanish. 1. Press and release the REVIEW up button then hold down the REVIEW down button. “SETUP MENU ^ v” appears. 2. Press the REVIEW up button until “CID LANGUAGE” appears. 3. Press the DELETE button to show the current language setting. The default is English. 4. Press REVIEW up or down to change the language. 5. Press DIAL to store the language and return to the “CID LANGUAGE” display. TO SET THE LCD CONTRAST This adjustment allows optimization of the contrast and viewing angle of the display. 1. Press and release the REVIEW up button then hold down the REVIEW down button. “SETUP MENU ^ v” appears. 2. Press the REVIEW up button until “LCD CONTRAST” appears. 3. Press the DELETE button to show the current contrast setting. There are 5 levels of contrast, with the default set to 3. 4. To decrease the contrast, press REVIEW down. To increase, press REVIEW up. 5. Press DIAL to store the contrast setting and return to the “LCD CONTRAST” display. TO SET THE DIAL MODE This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing. 1. Press and release the REVIEW up button then hold down the REVIEW down button. “SETUP MENU ^ v” appears. 2. Press the REVIEW up button until “T/P DIAL MODE” appears. 3. Press the DELETE button to show the current dial mode. The default is set to tone. 4. To change the dial mode, press REVIEW up or down. The display will alternate between the two modes. 5. Press DIAL to store the dial mode and return to the “T/P DIAL MODE” display. TO EXIT SETUP To exit the setup mode after your changes have been made, you can immediately exit by selecting the “EXIT SETUP” menu and pressing the DIAL button. NOTE: The phone will exit setup after 10 seconds if no buttons are pressed. REMINDER: The time and date are programmed automatically when the first Caller ID information is successfully received after setup. INSTALLING THE PHONE TO INSTALL ON A DESKTOP 1. Plug the coiled cord into the handset. Plug the other end into the jack on the bottom end of the base. 2. Plug the long straight line cord ...