Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
If you want to connect to a remote site using leased line WAN links see “Setting Up a WAN Link” on page 1- 29. If you are unsure about the networking configuration you require, see “Examples of Typical ISDN Networking Applications” on page 1- 31 for more information. IMPORTANT The Quick Configuration menu option is designed to be used only when you set up the unit for the first time. If you want to make any changes to the unit’s configuration at a later stage, you should use the management system menus to make these changes. For more information, see the Software Reference guide. Starting Quick Configuration Using a VT100 compliant terminal emulator, setup the terminal emulation to VT100 with communications parameters set as follows; select the COM port to be Quick Configuration 1- 19 used for data transmission, 9600 bits/s – 8 data bits – 1 stop bit – no parity, with flow control set to none. Example Using Windows 3.1 Terminal Application Start the Windows ‘ Terminal’ application. Using a mouse, click on Settings in the status bar to reveal the menu. From the menu: a Select the Terminal Emulation dialog box; confirm that DEC VT-100 (ANSI) is selected. b Select the Communications dialog box; check the communications parameters are set as above. c Select the Terminal Preferences dialog box; confirm that all check-boxes have been cleared. Should the cursor disappear during configuration, confirm that the Cursor Blink check-box has been checked (i.e. shows a cross in it). Should the keyboard arrow keys fail to move the cursor during configuration, confirm that the ‘Use Function, Arrow, and Ctrl Keys for Windows’ check-box has not been checked. d Now save this configuration as terminal emulator file for future use. 1-20 CHAPTER 1: GETTING STARTED 1-20 CHAPTER 1: GETTING STARTED If you are using Windows 95, use the Hyperterminal 3 Enter the default password, PASSWORD using application and configure it in the same way as uppercase characters. The Main Menu appears as described above. shown in Figure 1-8. Figure 1-8 The Main Menu Screen If the terminal emulator has been correctly configured, pressing [RETURN] displays the Enter Password screen. Figure 1- 9 Quick Configuration Menu 4At the command prompt enter QC The screen changes to display the Quick Configuration menu Figure 1- 9. You can configure the unit to connect to other Novell networks, to bridge to hosts on the same IP network (a network with the same IP network address), to route to a different IP network (an IP network with a different IP network address) and to connect to the Internet or other Point-to-Point Protocol (PPP) router. By using the commands several times, you can configure the unit to automatically connect to a combination of the above networks or to several different networks of the same type. For example, if you need to connect to an IPX site, an IP host on a different network and to the Internet using an ISDN connection to your Internet service provider you would do the following. ¦ Use the NO command to configure the connection to the Novell server at the remote site. ¦ Use the IPR command to configure the connection to the remote IP host. ¦ Use the IN command to configure the connection to your Internet service provider’s router. You cannot configure the unit to be IP router at the same time. Quick Configuration 1- 21 The OfficeConnect Remote talks to other OfficeConnect Remote units using its own very efficient FastConnect protocol over the ISDN or WAN port connections. If you need to communicate with another manufacturer’s equipment, then you need to configure the OfficeConnect Remote to use the PPP protocol using the Internet option. See later in this section for more information. You can further configure the PPP parameters using the management system. See the Software Reference guide for more information. Before configuring the unit to use PPP, you should check with your Internet service provider or with the system administrator of the remote site to find out which PPP parameters should be set and what their values should be. Do not attempt to configure the unit to use PPP without this information. Setting the Unit Name Before you configure the unit to connect to any other network, you must first give the unit a name. Enter NA at the command prompt on the Quick Configuration screen to display the screen illustrated in Figure 1-10. The fields on this screen are: Unit Name Type in a suitable name for this unit. The name can be up to 12 characters long, must contain no spaces and should, where possible, give an indication of the geographical location of the unit or the name of the users. Manager LAN IP Address Type the IP address for this unit. It must be a unique IP address on your network. Manager LAN IP Mask Enter an appropriate IP subnet mask. See “Subnet Masking” in Appendix A for more information about subnet masks. Network Type Toggle the network type to match the ISDN service provided by your ISDN service provider. Figure 1-...
Este manual também é adequado para os modelos :Controle remoto - 520 (1.34 mb)
Controle remoto - 530 (1.34 mb)